Maintenance Advice; Making The Bed; Removable Lining; Disassembling The Crib - Chicco next2me Instructions For Use Manual

the red buckle to form a loop (fig. 25). Repeat this operation
on the other side. For easier installation, during fixing of the
buckles, we suggest that the crib is kept at a short distance from
the parent's bed.
14. At this point, move the crib to the side of the parent's bed
and tighten the loop by pulling the belts firmly (fig. 26). Carry
out this operation on one side and then on the other side,
adjusting the belts until the crib is firmly in contact with the
parents mattress. WARNING: before every use always check to
make sure that there is no space between the parent's mattress
and the side of the crib. If there is, pull the belts firmly to
tighten until there's no space and the permitted condition of
use has been restored.
15. Store any excess of belts inside the pocket positioned on the
bottom of the fabric lining.
16. Lock the wheels of the crib as described in point 7.
If, during the fixing operations of the crib to the parent's bed,
it is not possible to slide the feet of the crib under the parent's
bed, it is still possible to fix the crib following the operations
described in the previous points by rotating the adjustable feet
during alignment of the crib to the bed.
In order to rotate the feet pull the rotation release button using
one hand and turn the feet of the crib inward (fig. 27).
WARNING: Use of the product is only permitted with beds and/
or mattresses with straight sides. Use of the product with round
beds and/or mattresses or water beds is not permitted.
WARNING: When the product is used in the "Co-Sleeping
Mode" (fixing to the bed, it should always be fitted to the long
side of access to the bed. DO NOT fix the product to the head
or bottom of the bed.

MAINTENANCE ADVICE

The crib and the mattress have a resistant fabric cover, which is
completely removable and washable.
The removal/application activities should be carried out by
adults only. On a regular basis check the condition of the
product and the presence of any possible damage. In the case
of damage do not use it and keep it out of the reach of children.
For washing of the fabrics, carefully comply with the instructions
indicated on the label.
For cleaning do not use solvents, abrasive products or aggressive
products.
Hand wash in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
After each wash check the resistance of the fabric and of the
stitching.
WARNING: During the removal and/or application of the lining,
handle the fabric carefully in order to avoid accidental damage
or tears.
WARNING: the removal and/or application operations may
take a few minutes and should be carried out by an adult.

MAKING THE BED

It is possible to unfasten the crib from the parents' bed in order
to make the bed easily. Just unfasten the grey buckles located
below the fabric finish.
To re-secure the crib to the parents' bed, pull once again the
belts to make sure the crib is properly and firmly secured to the
parents' bed. Pay attention to follow all the steps previously
mentioned in paragraph ''co-sleeping mode (Fixing to the bed)''.

REMOVABLE LINING

17. Remove the mattress and release the buttons on the lower
part of the fabric structure (fig. 28).
18. Press the buttons located on the legs' fastening point (fig.
29) and pull the upper tubular structure upward, removing the
fabric lining from the legs (fig. 30). Perform these operations
on both sides.
Open the lateral zips on the window opening and press the
release buttons of the upper removable tubular structure as
explained in paragraph ''co-sleeping mode (Fixing to the bed)''.
Then pull out the removable upper tubular structure (fig. 31),
paying attention not to damage the internal part of the lining.
19. Open the zip located on the upper edge of the crib and
remove the fabric lining completely (fig. 32).
20. Remove the rigid support of the rail (fig. 33).

DISASSEMBLING THE CRIB

The crib can be fully disassembled in order to store it in the bag
supplied with the product. To disassemble the crib, repeat the
operations described in points 17-18 of paragraph ''Removable
lining''. Then unfasten the central support structure by pressing
the fastening pins on both crib's legs (fig. 34).
20