Table of Contents
Advertisement
Quick Links
EQUIPMENT
SELECTION
. . . . . . . . . . . . .
Model 464
Heavy Duty with 8 inch Blade
Heavy Duty with 16 inch Blade
End Cutting with 8 inch Blade
End Cutting with 16 inch Blade
Blades
16 inch end cutting
8 inch end cutting
. . . . . . . . . . . . .
8 inch heavy duty
. . . . . . . . . . . . .
16 inch heavy duty
Supports
16 inch heavy duty
8 inch heavy duty
. . . . . . . . . . . . .
8 inch end cutting
. . . . . . . . . . . . .
16 inch end cutting
Accessories
Air Hose, 16 ft
. . . . . . . . . . . . . . . .
Air Filter/Regulator/Lubricator
Balancer (for all models)
JARVIS
6205002
Ordering No.
. . .
4005260
.
4005261
. .
4005262
.
4005263
. . . . . . . . . . . .
1023121
1023122
1023123
. . . . . . . . . . . .
1023124
. . . . . . . . . . . .
1058072
1058073
1058076
. . . . . . . . . . . .
1058077
1059015
. .
3022003
. . . . . . .
4042045
Model 464 Wellsaw
Air Powered Reciprocating
TABLE OF
CONTENTS
. . . . . . . . . . . . . . . . . . . . . . . . .
• Safety Messages to Employer and
Safety Director
• Safety Messages to Operators,
Maintenance and Cleanup Personnel 3
• Parts Diagram and List
• Specifications
• Installation Instructions
• Operation Instructions
• Maintenance Instructions
PRODUCTS CORPORATION
®
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA E--MAIL.
TEL. 860-347-7271
Saw
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . .
jarvis.products.corp@snet.net
jarvisproducts.com
FAX. 860-347-6978
WWW.
Page
2
4
6
6
6
6
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Jarvis 464
Summary of Contents for Jarvis 464
- Page 1 Model 464 Wellsaw Air Powered Reciprocating EQUIPMENT TABLE OF SELECTION ... . . Ordering No. CONTENTS ......
- Page 2 10. Avoid injury. Do not permit the tool to be misused. 11. If you resell or distribute a Jarvis product, you must provide the purchaser with the appropriate safe- ty sheets and tool brochure. Additional copies of safety sheets and tool brochures will be provided upon request.
- Page 3 MODEL 464 Wellsaw page 3 of 8 Keep hands clear. SAFETY MESSAGES TO OPERATORS, MAINTENANCE AND CLEANUP PERSONNEL REMOVE ANY MALFUNCTIONING TOOL FROM SERVICE REPORT ANY PROBLEMS TO YOUR SUPERVISOR 1. Disconnect the power supply in accordance with OSHA’s lockout/tagout procedures (29 CFR 1910.147) before changing the blade.
- Page 4 MODEL 464 Wellsaw page 4 of 8 ITEM PART NO. PART NAME 1022060 Valve Seat 3022025 Upper Valve Body w/item 9 1035194 Seal 1016211 Gear Housing 1055948 Socket Head Cap Screw 1035198 Gasket 1002194 Bearing Cover...
- Page 5 MODEL 464 Wellsaw page 5 of 8 Air Outlet ITEM PART NO. PART NAME 1011294 Coupling 1020251 Gear Shaft 1004277 Thrust Washer 1021367 Long Inner Race 1016428 Rear Motor Housing 1021217 Long Needle Bearing 1021218 Thrust Bearing...
-
Page 6: Specifications
2.4 Both hands should be on the saw at all times INSTALLATION INSTRUCTIONS while cutting. Continue holding the tool with 1 Suspend the Model 464 Wellsaw from a balancer. both hands until the saw blade comes to a com- Jarvis part number 4042045 is available. -
Page 7: Maintenance Instructions
IMPORTANT: ALWAYS DISCONNECT THE COM- 4 BLADE REMOVAL: PRESSED AIR SUPPLY IN ACCORDANCE WITH NOTE: Your Jarvis Wellsaw is equipped with a hex key OSHA’S LOCKOUT/TAGOUT PROCEDURES (29 CFR (item 81) for removing the blade. This wrench is located 1910.147) WHEN INSTALLING OR REMOVING THE in the housing directly behind the blade support. - Page 8 MODEL 464 Wellsaw page 8 of 8 c. Tighten the set screw (item 80) with the hex (item 78) and push rod (item 84). key (item 81). 8.9 Insert a small block of wood between the crank arm (item 73) and the gear housing (item 21) to HEAVY DUTY BLADE SUPPORT (Heavy Duty): a.
Need help?
Do you have a question about the 464 and is the answer not in the manual?
Questions and answers