Table of Contents
Advertisement
Quick Links
IMPORTANT:
•
• The glass tube will be extremely
hot when it is working so never
try to touch it and keep children
away.
• Turn off the appliance
immediately if it starts raining
and never use it while it is
raining as the glass tube may
break when it comes in contact
with water.
• Never splash any liquid onto
the glass tube when the
appliance is on.
• Always ensure the appliance
stands on a flat, firm surface as
the glass tube may break if the
appliance falls over.
• Never use the appliance if the
glass tube has any cracks or
damage.
Important: The installer or seller must leave these instructions with the consumer.
3948-05/14
Lava Outdoor Heater
Model No. GM124-015
Retain these instructions for future use.
FOR YOUR SAFETY
If you smell gas:
1. Shut off the gas to the
appliance.
2. Extinguish any open flame.
3. If odour continues,
immediately call your gas
supplier.
Do not store or use gasoline
or other flammable vapour and
liquids in the vicinity of this or any
other appliance.
WARNING:
Improper installation, adjustment,
alteration, service or maintenance
can cause injury or property
damage.
Read the instructions thoroughly
before installing or servicing this
equipment.
FOR OUTDOOR USE
ONLY
OPERATES ON
LPG/ULPG
Advertisement
Table of Contents
Related Manuals for Gasmate GM124-015
Summary of Contents for Gasmate GM124-015
- Page 1 Lava Outdoor Heater Model No. GM124-015 IMPORTANT: FOR YOUR SAFETY • • The glass tube will be extremely If you smell gas: hot when it is working so never 1. Shut off the gas to the try to touch it and keep children appliance.
-
Page 2: Installation
Installation, Operation and Maintenance Instructions INSTALLATION Combustible materials are considered to be wood, Important Safety Rules: compressed paper, plant fibres, plastic, plexiglas or This appliance must only be used in a well ventilated other materials capable of being ignited and burned. area. - Page 3 The hose assembly should be properly located out of Reconnect the regulator to the gas cylinder. pathways where people may trip over it. The hose Leak test the connection using a soapy water solution. must be protected from contact with hot or sharp Ensure no bubbles appear before proceeding.
- Page 4 PATIO Heater - For Outdoor Use Only Minimum Clearance from Combustible Surfaces*: 650mm 540mm Glass Tube Burner head Cylinder housing 600mm *Combustible materials are considered to be wood, compressed paper, plant fibres, plastic or other materials that are capable of being ignited and burned.
-
Page 5: General Assembly
GENERAL ASSEMBLY Connecting & Disconnecting to Gas Source 3. When connecting the hose to the cylinder tighten the IMPORTANT: Before connecting and nut to a positive stop by hand. disconnecting appliance to gas source, make 4. Open cylinder valve fully. If a leak can be heard sure control knob is in ‘OFF’... -
Page 6: Parts List
PARTS LIST Glass Tube Rubber Ring Middle Plate Control Box Front Panel Side Panel A Side Panel B With Handle Handle Knob with Chain Attach to the Front Panel Wheel Bottom Plate Screws M6X10 Fasten the Wheels to the Bottom Plate Screws M5X10 Round Fasten the Upper/Middle and Bottom Plate to the Aluminum Tubes Screws M5X10 Flat... -
Page 7: Assembly Instructions
ASSEMBLY INSTRUCTIONS Tools Required: 1 Phillips head screwdriver, 1 adjustable spanner. STEP 1. Attach the wheels (R) into the bottom plate (S) using the screws M6X10 (T). STEP 2. Mount the stability ring (X) to the base of the heater. STEP 3. Attach the bottom plate (S) into the aluminum tubes (C) with screws M5X10 round (U). - Page 8 ASSEMBLY INSTRUCTIONS STEP 4. Attach the middle plate (K) into the aluminum tubes (C) with screws M5X10 round (U). STEP 5. Use three side bolts with wing nuts (F) to pre-attach into the flame screen (E), then connect the upper plate (D) and flame screen (E) with three side bolts with screw nuts (G). STEP 6. Attach the whole upper plate with flame screen into the aluminum tubes (C) with screws M5X10 round (U).
- Page 9 ASSEMBLY INSTRUCTIONS STEP 7. Attach reflector (A) through the bolts, then tighten the shield with wing nuts (F). STEP 8. Put the rubber ring (J) into the middle plate hole, then insert the glass tube (I) into the heater by holding the base in one hand, top in the other, and insert the tube underneath the upper plate.
- Page 10 ASSEMBLY INSTRUCTIONS STEP 9. Assemble the control box (L) into the back of the middle plate with screws M5X10 flat (V). STEP 10. Assemble the handle (P) into the side panel B (O), then attach this panel (O) and other side panel A (N) in the heater by screws M5X10 flat (V).
- Page 11 ASSEMBLY INSTRUCTIONS STEP 11. Assemble the mesh guard (B) into the heater to match the hook in the aluminum tubes, then screw the guard fastening pieces (H) together with matching 3/16 screws on the top of the upper plate to keep the mesh guard and the flame screen firmly in place. STEP 12. Screw the knob with the chain (Q) into the front panel (M) and attach chain to the control box (L).
- Page 12 ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS STEP 13 STEP 14 Ensure cylinder valve is in its full off position. Check Turn on the gas cylinder ensuring that the control knob for any damage to either the cylinder connection or on the outdoor heater is turned OFF at this point. DO NOT ATTEMPT TO LIGHT THE HEATER!!.
-
Page 13: Troubleshooting
TEST FIRING THE APPLIANCE TEST FIRING THE APPLIANCE Test fire appliance, following the lighting instructions on. Leak test all gas connections with soapy water. Soap bubbles indicate gas leakage. DO NOT use a match to test for gas leaks. WARNING: White smoke may appear around the burner during the first minute of the initial firing. TROUBLE SHOOTING Problem Possible Causes... -
Page 14: Safe Appliance Locations
The following figures are diagrammatical representations of outdoor areas. Rectangular areas have been used in these figures - the same principles apply to any other shaped area. Distributed by: Aber, Hamilton, N.Z. Gasmate ® is a registered trademark of: Sitro Group Australia Pty Ltd www.gasmate.com.au www.gasmate.co.nz Aber, Hamilton, N.Z. www.gasmate.co.nz...