Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for IDTECH ValueScan II
Summary of Contents for IDTECH ValueScan II
- Page 1 ValueScan II Barcode Scanner Quick Start Manual...
-
Page 2: Fcc Warning Statement
FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 3: Limited Warranty
ID TECH is a registered trademark of International Technologies & Systems Corporation. ValueScan II and Value through Innovation are trademarks of International Technologies & Systems Corporation. - Page 4 Section 1 INTRODUCTION The ValueScan II is the ideal scanner for retail applications. Its light- weight, easy-to-handle form factor makes scanning a breeze. Operation is intuitive, no warm up or waiting: Just point and scan! The ValueScan II reads all commonly used barcode symbologies from contact up to a distance of 125mm.
- Page 5 Section 2 INSTALLATION AND OPERATION Installation- Keyboard Wedge 1. First of all, you must switch off power for the terminal/computer. 2. Disconnect the keyboard cable from the back of the terminal/computer and connect to the interface cable of the scanner. 3.
-
Page 6: Pin Assignments
Pin Assignments Keyboard Wedge Connector (To Host Side): Mini-DIN 6P Male Mini-DIN 6P Female DATA / PC CLK / KB DATA / KB VCC (+5V) VCC (+5V) CLK / PC Mini-DIN 6P Female Connector Mini-DIN 6P Male Connector RS-232 DB-9F Connector (To Host Side): Definition VCC (+5V) - Page 7 Scanning mode: Good-read off-The trigger button must be pressed to activate scanning. The light source of imager stops scanning when there is a successful reading or no code is decoded after the Stand-by duration elapsed. Momentary-The trigger button acts as a switch. Press button to activate scanning and release button to stop scanning.
- Page 8 Program Option Bar Code Option Alphanumeric Entry Good-read off Momentary 01＊ Alternate Timeout off Continue Scanning mode Test only 01-99 (second) 00-99 06＊ Stand-by duration 01-99 (10 msec) 01-99 50＊ Double read timeout 00-09 00-09 (00: no double confirm) 00＊ Double confirm 00-64 00-64...
- Page 9 Finish...
-
Page 10: Troubleshooting
Section 3 TROUBLESHOOTING Troubleshooting assistance for common problems: • The data from the Scanner is not as expected. ANS: Please download full User’s Manual and follow all instructions. • The Scanner does not output data. . ANS: Check basic operation: connect the cable; see if the desired barcode type (symbology) is enabled. - Page 11 Reset Scanner to factory default settings If you wish to return the scanner to all the factory default setting, scan the Default value initialization bar code. Step 1. Program Step 2. Default Step 3. Exit Firmware version list If you wish to display the firmware version, scan the Firmware version list.
-
Page 12: Specification
Section 4 SPECIFICATION ValueScan Specification Operational Light Source 660 nm Visible Red LED Optical System 2048 pixel CCD (Charge-coupled device) Depth of Scan Field 0-180 mm (CODE 39, 500Lux, PCS=90%, 20mils) Scanning Width 50 mm wide @ 10mm Scan Speed 100 scans/sec Resolution 0.1mm (4mils) Code39,PCS=90%... - Page 13 Operating Temperature 0℃ to 45℃ (32℉ to 113℉) Storage -20℃ to 60℃ (-4℉ to 140℉) Humidity 10% to 90% relative humidity, non-condensing Light Level Up to 20000 Lux Shock 1.5m drop onto concrete Contaminants Seals to resist airborne particulate contaminants Ventilation None required Programming...
- Page 14 Section 5 READING MODE SETTINGS Default setting For each barcode shown as below: V = Enabled as default setting - = Not supported Empty space = Download User’s Manual; Please visit IDTECH website: www.idtechproducts.com Checksum Checksum Read Code Code Type...
-
Page 15: Testing Codes
Section 6 TESTING CODES UPC-E UPC-A Interleaved 2 of 5 Code 39 Code 128 UCC/EAN-128 Full User’s Manual is available for download on www.idtechproducts.com... - Page 16 ID TECH 10721 Walker Street Cypress, CA 90630 (714) 761-6368 www.idtechproducts.com 80104501-001 rev.B...