Page 1 2DScan FX100 Barcode Scanner Scanner User's Manual 80108506-001 rev.B...
Page 2: Table Of Contents
Table of Contents 请更换节标题 Content About this guide Idtech Auto-ID Support Center ........................2 Getting to Start Introduction ..............................3 Unpacking ..............................4 Unpacking ............................. 4 Outline of FX100 ..........................4 Data Interface ............................5 Communication Ports ..........................6 Connecting with USB Cable ........................7 Connecting with RS232 Cable ........................
Page 3 Table of Contents RS232 Interface Introduction ..............................25 Serial Port ..............................26 Baud Rate ............................26 Parity Check ............................27 Hardware Auto Flow Control ......................27 Data Bits Transmitted ......................... 28 Stop Bits .............................. 28 USB Interface Introduction ..............................29 USB HID-KBW ............................
Page 4 Table of Contents 2 Digits Addenda Code ........................50 5 Digits Addenda Code ........................50 EAN-8 expand to EAN-13 ........................51 EAN-13 ..............................52 Load Factory Default .......................... 52 Disable/EnableEAN-13 ........................52 Check Digit ............................52 2 Digits Addenda Code ........................53 5 Digits Addenda Code ........................
Page 5 Table of Contents Code 93 ..............................76 Load Factory Default .......................... 76 Enable /Disable Code 93 ........................76 Select Message Length ........................77 Check Digit ............................78 UCC/EAN-128 ............................79 Load Factory Default .......................... 79 Enable/Disable UCC/EAN-128 ......................79 GS1 Databar ............................... 80 Load Factory Default ..........................
Page 6 Table of Contents QR Code ..............................101 Load Factory Default ........................101 Enable/Disable QR Code ........................101 Select Message Length ........................102 QR Twin Code ..........................103 Aztec ................................ 104 Load Factory Default ........................104 Enable/Disable Aztec ........................104 Select Message Length ........................105 Reading Multi-barcodes of an Image....................
Page 7 Table of Contents Message Interception & Pack Introduction .............................. 128 Message Interception ..........................129 Programming 1D Intercept Option ....................130 Programming 2D Intercept Option ....................131 Message Pack ............................132 Introduction ............................132 Normal Pack ............................. 132 Batch Programming Introduction .............................. 133 How to build a batch command .......................
Page 8: About This Guide
About this guide Introduction This FX100 Embedded 1D/2D Barcode Scanner Integration Guide provides general instructions for OEM integration. Graphic Notations Tool – Handy item for a task. Attention – Important subject to be aware of or to avoid. Tips – Helpful information about a topic or a feature. Example –...
Page 9: Introduction
Getting to Start Introduction FX100 is an omnidirectional imager capture,decode and transfer 1D & 2Dbarcode This chapter presents an overall picture of how to use FX100 step by step. Please have an FX100 handy. This chapter is recommended to general users, maintenance personnel, and software programmers. Page 3...
Page 10: Unpacking
Getting to Start Unpacking Unpacking Unpack FX100 and accessories. Check with the packing list. Make sure that there is no damage or missing part(s). If any damage or missing parts, please keep the original package and contact your supplier for services.
Page 11: Data Interface
Getting to Start Unpacking Data Interface PIN 10 PIN 1 Cable Slot Function Type Name Null Null Power DC5V Serial Port Output，RS232 Serial Port Input，RS232 Null Null Ground USB Data Signal Page 5...
Page 12: Communication Ports
Getting to Start Communication Ports FX100 must connect to a Host to operate. A Host can be PC, POS, or any intelligent terminal with at least one of the following communication ports: USB, RS232, or PS/2. 1、 USB port on Host： 2、...
Page 13: Connecting With Usb Cable
Getting to Start Connecting with USB Cable 1、 Insert USB Cable (RJ45 male head) into FX100 cable slot; 2、 Insert USB Cable (USB male head) into Host’s (female) USB connector; Page 7...
Page 14: Connecting With Rs232 Cable
Getting to Start Connecting with RS232 Cable 1、 Insert RS232 cable (RJ45 male head) into FX100 cable slot; 2、 Insert RS232 cable (RS232 male head) into Host’s (female) RS232 connector; 3、 Connect RS232 cable and the mains with power adapter; Page 8...
Page 15: Decode Zones
Getting to Start Decode Zones 36° 35mm Code39(10mil) 170mm 55mm Code39(15mil) 210mm 55mm PDF417(10mil) 175mm 60mm PDF417(15mil) 205mm 45mm Data Matrix(10mil） 145mm 45mm Data Matrix(15mil） 175mm 45mm QR Code(10mil） 140mm 50mm QR Code(15mil） 175mm Page 9...
Page 16: Speciﬁcations
Getting to Start Speciﬁcations Performance Image Sensor CMOS Resolution 752 * 480 Interface RS232 / USB 1.1 PDF417, QR Code(Model 1/2), DataMatrix(ECC200, ECC000, 050, 080,100,140), Aztec, Maxicode, etc. Symbologies Code128, EAN-13, EAN-8, Code39, UPC-A, UPC-E, Codabar, Interleaved 2 of 5, ISBN/ISSN, Code 93, etc Precision ≥...
Page 17: Dimensions Of Fx100 Unit
Getting to Start Dimensions of FX100 Unit M3 machine skew 11 7mm 26mm 36mm 50mm 10mm 12mm 60mm Figure 1. FX100 Top View Page 11...
Page 18: Programming The Engine
Programming the Engine Introduction There are 3 ways to program (conﬁgure) the Engine, Code Programming, Command Programming, and QuickSet Programming. Code Programming The Engine reads a set of specially encoded barcodes to program features. In the following sections, we will explain the options and features available and provide the barcodes to program them.
Page 19: Programming Notation
Programming the Engine Programming the Engine Programming Notation Tools Code Programming ON Code Programming OFF ** Code Programming OFF 【Pro CMD：0006000】 This is the notation to disable the Code Programming. There are 4 parts of a notation: 1、 The ﬁrst part of the notation is the barcode for Code Programming 2、...
Page 20: Code Programming On/Off
Programming the Engine Programming the Engine Code Programming On/Off Tools Code Programming ON Read the “Code Programming ON” barcode to activate “Code Program- ming” function. One or more Code Programming barcodes can be read to configure the Engine. If an option or feature needs additional parameters, such as digits, they can be found at the end of this chapter.
Page 21: Illumination
Programming the Engine Programming the Engine Illumination Tools Code Programming ON Illumination LED lighting up barcodes are used to capture better images. There are 4 modes: “Illumination Wink”: LED keeps flashing when reading » Code Programming OFF “Illumination Keep ON”: LED keeps on when Power ON »...
Page 22: Aiming
Programming the Engine Programming the Engine Aiming Tools Code Programming ON There are 3 modes: “Aim Wink”: LED keeps flashing when reading » “Aim Keep ON”: LED keeps on when Power ON » Code Programming OFF ** Aim Wink 【Pro CMD：0201000】 Aim Keep ON 【Pro CMD：0201010】...
Page 23: Beep
Programming the Engine Programming the Engine Beep Tools Code Programming ON Decoding Beep Read “Beep ON” to enable all decoding beep denotation and read “Beep OFF” to disable. Code Programming OFF **Beep ON 【Pro CMD：0203010】 Beep OFF 【Pro CMD：0203000】 Decoding Beep Type **Type 1 【Pro CMD：0203020】...
Page 24: Decoding Beep Volume
Programming the Engine Programming the Engine Beep Tools Code Programming ON Decoding Beep Volume ** Loud Code Programming OFF 【Pro CMD：0203030】【Pro CMD：0203032】 Medium 【Pro CMD：0203031】 Power On Beep ** Beep On 【Pro CMD：0204001】 Beep OFF 【Pro CMD：0204000】 Beep Denotation (Beeper Deﬁnitions) Beep Denotation low-higher-higher-higher...
Page 25: Reading Mode
Programming the Engine Programming the Engine Reading Mode Tools Code Programming ON Auto Mode: The ambient luminance change in front of the engine auto- » matically initiates reading. After completion of reading, the engine goes to idle. Both luminance change and the Trigger can initiate reading when idle. Continuous Mode: Pull the Trigger line low to start reading.
Page 26: Reading Timeout And Delay
Programming the Engine Programming the Engine Reading Timeout and Delay Tools Code Programming ON One Reading Timeout：If the engine doesn't read any barcode during the timeout period, it will stop reading automatically. One Reading Timeout is valid in Auto mode. The default timeout is 3000ms. Same Barcode Reading Delay：It is used to avoid misreading on the same Code Programming OFF barcode (the same format and message) in a Same Barcode Reading Delay...
Page 27: Sensitivity
Programming the Engine Programming the Engine Sensitivity Tools Code Programming ON Sensitivity is how sensitive the engine is to ambient illumination change. » Sensitivity value is [1 .. 20] » The lower the sensitivity value is the higher sensitivity will be. The low- »...
Page 28: Exposure Imaging Mode
Programming the Engine Programming the Engine Exposure Imaging Mode Tools Code Programming ON Code Programming OFF ** Normal Exposure Mode 【Pro CMD：0321000】 Reﬂections Eliminating Mode 【Pro CMD：0321010】 Page 22...
Page 29: Default
Programming the Engine Programming the Engine Default Tools Code Programming ON Factory Default Read “Load All Factory Default” to reset all parameters to factory default. Applicable conditions: Code Programming OFF User options programming wrong configuration leads to reading mal- » function Forget details of previous programming and start over.
Page 30: Query Product Information
Programming the Engine Programming the Engine Query Product Information Tools Code Programming ON Product information could be obtained by reading "Query Product Information" barcode. The engine will send it to the Host immediately. “Power ON, Send Product Info”, the engine sends product information through serial port(only) to the Host after Power ON.
Page 31: Rs232 Interface
RS232 Interface Introduction When the engine is connected to the Host with RS232 cable, system will select RS232 connection by default. Under RS232 connection, the engine and the Host use the same communication parameters: baud rate, parity check, data bits select and stop bits select. Select RS232 Connection 【Pro CMD：1100000】...
Page 32: Serial Port
RS232 Interface RS232 Interface Serial Port Tools Code Programming ON The engine and the Host should use the same serial port parameters: baud rate, parity check, data bits and stop bits. The sequence is as follows: 9600 (baud rate), null (parity check), 8 (data bits), 1 (stop bits). Baud Rate Code Programming OFF Baud rate is the number of bits of data transmitted per second.
Page 33: Parity Check
RS232 Interface RS232 Interface Serial Port Tools Code Programming ON Parity Check Parity check options should be the same on the engine and the Host. Select Odd parity: If data has an odd number of 1 bits, the parity bit »...
Page 34: Data Bits Transmitted
RS232 Interface RS232 Interface Serial Port Tools Code Programming ON Data Bits Transmitted Select data bits transmitted to be 5, 6, 7 and 8. Ensure the selections on the engine and the Host are the same. Code Programming OFF ** 8 Data Bits 【Pro CMD：0103030】...
Page 35: Usb Interface
USB Interface Introduction When using a USB connection, the default protocol is USB COM Port Emulation. When only data transmission is needed through USB connection, USB HID-KBW option can be programmed. It emulates the unit’s transmission as a USB keyboard input. The Host receives keystrokes of the virtual keyboard.
Page 36: Usb Hid-Kbw
USB Interface USB Interface USB HID-KBW Tools Code Programming ON USB connection (no driver needed) supports simulating the Imager transmission to be a USB keyboard input. The Host receives keystrokes of the virtual keyboard. It works in “Plug and Play” base. There is no driver required. Code Programming OFF Select USB HID-KBW 【Pro CMD：1100020】...
Page 37: Usb Country Keyboard Types
USB Interface USB Interface USB HID-KBW Tools Code Programming ON USB Country Keyboard Types The keyboard arrangements and country codes vary in different countries. Refer country codes to the table “USB Country Keyboard Types”. Follow the steps mentioned below to program. Code Programming OFF 1、...
Page 38 USB Interface USB HID-KBW Country/Language Number Country/Language Number U.S. Netherlands(Dutch) Belgium Norway Brazil Poland Canada(French) Portugal Czechoslovakia Romania Denmark Russia Finland(Swedish) Slovakia France Spain Germany/Austria Sweden Greece Switzerland(German) Hungary Turkey F Israel(Hebrew) Turkey Q Italy Latin-American Japan Page 32...
Page 39: Unknown Characters, Beep
USB Interface USB Interface USB HID-KBW Tools Code Programming ON Unknown Characters, Beep HID-KBW deems an unknown character to be a character is not included in a country keyboard type. It may not be able to allocate and send a keystroke, thus lead to an error beep.
Page 40: Emulate Alt + Keypad
USB Interface USB Interface USB HID-KBW Tools Code Programming ON Emulate ALT + keypad When enabled, full ASCII characters (0x00～0xff) can be sent over the numeric key- pad regardless country keyboard selections. 1、 “ALT” Make Code Programming OFF 2、 According to the ASCII value, input the numbers over the numeric keypad 3、...
Page 41: Function Key Mapping
USB Interface USB Interface USB HID-KBW Tools Code Programming ON Function Key Mapping When enabled, function characters (0x00~0x1F) are sent as ASCII sequences over the numeric keypad. 1、 “Ctrl make” Code Programming OFF 2、 Hit function key 3、 “Ctrl Break” ** No Function Key Mapping 【Pro CMD：1103130】...
Page 42: Ascii Function Key Mapping Table
USB Interface USB HID-KBW ASCII Function Key Mapping Table ASCII(HEX) Function key ASCII(HEX) Function Key Page 36...
Page 43: Keystroke Delay
USB Interface USB Interface USB HID-KBW Tools Code Programming ON Keystroke Delay This parameter sets the delay, in milliseconds, between emulated keystrokes. Scan programming code below to increase the delay when the Host require a slower trans- mission of data. Code Programming OFF ** No Delay 【Pro CMD：1103050】...
Page 44: Convert Case
USB Interface USB Interface USB HID-KBW Tools Code Programming ON Convert Case The Imager converts all barcode messages to the selected case. Code Programming OFF ** No Case Conversion 【Pro CMD：1103040】 Convert All to Upper Case 【Pro CMD：1103041】 Convert All to Lower Case 【Pro CMD：1103042】...
Page 45: Emulate Numeric Keypad
USB Interface USB Interface USB HID-KBW Tools Code Programming ON Emulate Numeric Keypad Code Programming OFF When disable, the whole barcode message will be emulated as keystrokes on main keyboard. Read “Emulate Numeric Keypad” to enable the function. when “0~9”is of the barcode message, it will be emulated as keystrokes on numeric keypad.
Page 46: Usb Datapipe
USB Interface USB Interface USB DataPipe Tools Code Programming ON A driver has to be installed before.using this protocol to communicate with reader, The advantage of using this protocol is the fast data transmission. Meanwhile, the SDK can be easily integrated into the application system. Code Programming OFF Select USB DataPipe 【Pro CMD：1100010】...
Page 47: Usb Com Port Emulation
USB Interface USB Interface USB COM Port Emulation Tools Code Programming ON When the USB port is connected to Host serial port in order to receive data from scanner, the model of imitating USB-to-RS232 has to be chosen. Hence, the engine and the Host must communicate at the same parameters and the parameters of real serial port and visual serial port must be the same.
Page 48: Hid-Pos
USB Interface USB Interface HID-POS Tools Code Programming ON Introduction The HID POS interface is recommended for new applications. It can send up to 56 characters in a single USB report and is muchfaster than keyboard emulation. Features: » Code Programming OFF HID based, no custom driver required »...
Page 49: Access The Device In Your Program
USB Interface USB Interface HID-POS Tools Code Programming ON Access the Device in Your Program CreateFile opens the device as a HID, then ReadFile delivers the scanned data to the application. Use WriteFile to send data to the device. For complete information on USB and HID interfaces, please see www.USB. Code Programming OFF org.
Page 50: Symbols
Symbols Introduction This chapter lists all the available symbols and provides the programming barcodes to enable/disable them. Disabling reading of the symbols which do not apply, will improve reading performance. The few abling reading of the symbols are, the fast the engine will work. Page 44...
Page 51: General Options
Symbols General Options Tools Code Programming ON Disable Reading All Disable Reading All = Allow reading Programming Codes only. Code Programming OFF Disable Reading All 【Pro CMD：0001010】 Enable Reading All Enable Reading All = Enable to read all symbols and Programming Codes. Enable Reading All 【Pro CMD：0001020】...
Page 52: Enable Reading All 2D
Symbols General Options Tools Code Programming ON Enable Reading All 2D Code Programming OFF Enable Reading All 2D 【Pro CMD：0001060】 Disable Reading All 2D Disable Reading All 2D 【Pro CMD：0001050】 Page 46...
Page 53: Code 128
Symbols Code 128 Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Code 128 Factory Default 【Pro CMD：0400000】 Enable/Disable Code 128 Disable Code 128 【Pro CMD：0400010】 ** Enable Code 128 【Pro CMD：0400020】 When the engine can not read Code 128, please read“Enable Code 128” and try again. Page 47...
Page 54: Select Message Length
Symbols Code 128 Tools Code Programming ON Select Message Length It is used to program the valid reading length of Code 128. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Code 128 Message Length is deﬁned by “Min.
Page 55: Load Factory Default
Symbols EAN-8 Tools Code Programming ON Load Factory Default Code Programming OFF ** Load UCC/EAN-8 Factory Default 【Pro CMD：0401000】 Enable/Disable UCC/EAN-8 ** Enable UCC/EAN-8 【Pro CMD：0401020】 Disable UCC/EAN-8 【Pro CMD：0401010】 Check Digit UCC/EAN-8 is ﬁxed 8 digits barcode and the last digit is check digit. **Transmit Check 【Pro CMD：0401040】...
Page 56: Digits Addenda Code
Symbols EAN-8 Tools Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code. Picture below shows an ordinary code with a 2 digits Addenda Code. The left one in blue lines is an ordinary code. The right one in red lines is the 2 digits Addenda Code.
Page 57: Expand To Ean-13
Symbols EAN-8 Tools Code Programming ON EAN-8 expand to EAN-13 Expand EAN-8 to EAN-13, by adding 5 bytes of “0” to the left, and then transmit. Code Programming OFF ** Do Not Expand to EAN-13 【Pro CMD：0401090】 Expand to EAN-13 【Pro CMD：0401100】...
Page 58: Load Factory Default
Symbols EAN-13 Tools Code Programming ON Load Factory Default ** Load EAN-13 Factory Default 【Pro CMD：0402000】 Code Programming OFF Disable/EnableEAN-13 ** Enable EAN-13 【Pro CMD：0402020】 Disable EAN-13 【Pro CMD：0402010】 Check Digit ** Transmit Check 【Pro CMD：0402040】 Do Not Transmit Check 【Pro CMD：0402030】...
Page 59: Digits Addenda Code
Symbols EAN-13 Tools Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code. Picture below shows an ordinary code with a 2 digits Addenda Code. The left one in blue lines is an ordinary code. The right one in red lines is the 2 digits Addenda Code.
Page 60: Upc-E
Symbols UPC-E Tools Code Programming ON Load Factory Default ** Load UPC-E Factory Default 【Pro CMD：0403000】 Code Programming OFF Disable/Enable UPC-E ** Enable UPC-E 【Pro CMD：0403020】 Disable UPC-E 【Pro CMD：0403010】 When the engine can not read UPC-E, please read “Enable UPC-E” and try again. Check Digit UPC-E is ﬁxed 8 digits barcode and the last digit is check digit.
Page 61: Digits Addenda Code
Symbols UPC-E Tools Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code. Picture below shows an ordinary code with a 2 digits Addenda Code. The left one in blue lines is an ordinary code. The right one in red lines is the 2 digits Addenda Code.
Page 62: Transmit Default "0
Symbols UPC-E Tools Code Programming ON Transmit Default “0” The ﬁrst byte of UPC-E is default to “0”. Code Programming OFF ** Do Not Transmit “0” 【Pro CMD：0403090】 Transmit “0” 【Pro CMD：0403100】 UPC-E Expand to UPC-A Follow the standard algorithm to expand UPC-E to UPC-A. **Do Not Expand to UPC-A 【Pro CMD：0403110】...
Page 63: Upc-A
Symbols UPC-A Tools Code Programming ON Load Factory Default ** Load UPC-A Factory Default 【Pro CMD：0404000】 Code Programming OFF Disable/Enable UPC-A ** Enable UPC-A 【Pro CMD：0404020】 Disable UPC-A 【Pro CMD：0404010】 When the engine can not read UPC-A, please read “Enable UPC-A” and try again. Check Digit UPC-A is ﬁxed 13 digits barcode and the last digit is Check Digit.
Page 64: Digits Addenda Code
Symbols UPC-A Tools Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code. Picture below shows an ordinary code with a 2 digits Addenda Code. The left one in blue lines is an ordinary code. The right one in red lines is the 2 digits Addenda Code.
Page 65: Transmit Default "0
Symbols UPC-A Tools Code Programming ON Transmit Default “0” The ﬁrst byte of UPC-A is default to “0”. Code Programming OFF **Do Not Transmit “0” 【Pro CMD：0404090】 Transmit “0” 【Pro CMD：0404100】 UPC-A has the default “0” but it is not printed out, unlike UPC-E. Read “Transmit 0”...
Page 66: Interleaved 2 Of 5
Symbols Interleaved 2 of 5 Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Interleaved 2 of 5 Factory Default 【Pro CMD：0405000】 Disable/Enable Interleaved 2 of 5 ** Enable Interleaved 2 of 5 【Pro CMD：0405020】 Disable Interleaved 2 of 5 【Pro CMD：0405010】...
Page 67: Select Message Length
Symbols Interleaved 2 of 5 Tools Code Programming ON Select Message Length It is used to program the valid reading length of Interleaved 2 of 5. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
Page 68: Check Digit
Symbols Interleaved 2 of 5 Tools Code Programming ON Check Digit Interleaved 2 of 5 may include Check Digit (not compulsory) following its barcode messages. It veriﬁes the barcode message. “NO Check, Transmit All” means to read without check and transmit »...
Page 69: Speciﬁed Lengths
Symbols Interleaved 2 of 5 Tools Code Programming ON Specified Lengths Program the engine to read speciﬁed lengths or ranges of speciﬁed lengths for Interleaved 2 of 5. The length value must be 3 decimal digits. And the length value MUST be an even number between 2 to 64. Read “Enable Speciﬁed Length”...
Page 70: Itf-14
Symbols ITF-14 Tools Code Programming ON ITF-14 is a ﬁxed length, 14 bytes Interleaved 2 of 5 barcode with Check digit. By factory default, it is disabled. When enabled, ITF-14 precedes 14-byte Interleaved 2 of 5 barcode. Code Programming OFF **Disable ITF-14 【Pro CMD：0405080】...
Page 71: Itf-6
Symbols ITF-6 Tools Code Programming ON ITF-6 is a ﬁxed length 6 bytes Interleaved 2 of 5 barcode with check digit. When enabled, ITF-6 precedes 6-byte Interleaved 2 of 5 barcode. Code Programming OFF **Disable ITF-6 User Selection 【Pro CMD：0405110】 ITF-6, Read, Do Not Transmit Check Digit 【Pro CMD：0405120】...
Page 72: Matrix 2 Of 5
Symbols Matrix 2 of 5 Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Matrix 2 of 5 Factory Default 【Pro CMD：0406000】 Matrix 2 of 5 Disable/Enable Enable Matrix 2 of 5 【Pro CMD：0406020】 ** Disable Matrix 2 of 5 【Pro CMD：0406010】...
Page 73: Select Message Length
Symbols Matrix 2 of 5 Tools Code Programming ON Select Message Length It is used to program the valid reading length of Matrix 2 of 5. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
Page 74: Check Digit
Symbols Matrix 2 of 5 Tools Code Programming ON Check Digit Matrix 2 of 5 may include Check Digit (not compulsory) following its barcode messages. It veriﬁes the barcode message. “NO Check, Transmit All” means to read without check and transmit »...
Page 75: Code 39
Symbols Code 39 Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Code 39 Factory Default 【Pro CMD：0408000】 Enable/Disable Code 39 ** Enable Code 39 【Pro CMD：0408020】 Disable Code 39 【Pro CMD：0408010】 When the engine can not read Code 39, please read “Enable Code 39” and try again Transmit Start &...
Page 76: Select Message Length
Symbols Code 39 Tools Code Programming ON Select Message Length It is used to program the valid reading length of Code 39. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
Page 77: Check Digit
Symbols Code 39 Tools Code Programming ON Check Digit Code 39 may include Check Digit (not compulsory) following its barcode message. It veriﬁes the barcode message. "NO Check, Transmit All" means to read without check and transmit » all bytes including barcode message and Check Digit. Code Programming OFF "Check, Do Not Transmit Check Digit"...
Page 78: Codabar
Symbols Codabar Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Codabar Factory Default 【Pro CMD：0409000】 Enable/Disable Codabar ** Enable Codabar 【Pro CMD：0409020】 Disable Codabar 【Pro CMD：0409010】 When the engine can not read Codabar, please read “Enable Codabar” and try again. Page 72...
Page 79: Select Message Length
Symbols Codabar Tools Code Programming ON Select Message Length It is used to program the valid reading length of Codabar. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Code Programming OFF Codabar Message Length is deﬁned by “Min.
Page 80: Check Digit
Symbols Codabar Tools Code Programming ON Check Digit Codabar may include Check Digit (not compulsory) following its barcode message. It veriﬁes the barcode message. "NO Check, Transmit All" means to read without check and transmit » all bytes including barcode message and Check Digit. Code Programming OFF "Check, Do Not Transmit Check Digit"...
Page 81: Transmit Start & Stop Character
Symbols Codabar Tools Code Programming ON Transmit Start & Stop Character Codabar uses either one of “A”, “B”, “C” and “D” as the start character and the stop character. Transmission of them can be selected. Code Programming OFF **Transmit Both Start & Stop Character 【Pro CMD：0409090】...
Page 82: Code 93
Symbols Code 93 Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Code 93 Factory Default 【Pro CMD：0410000】 Enable /Disable Code 93 ** Disable Code 93 【Pro CMD：0410010】 Enable Code 93 【Pro CMD：0410020】 When the engine can not read Code 93, please read “Enable Code 93” and try again. Page 76...
Page 83: Select Message Length
Symbols Code 93 Tools Code Programming ON Select Message Length It is used to program the valid reading length of Code 93. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
Page 84: Check Digit
Symbols Code 93 Tools Code Programming ON Check Digit Code 93 may include Check Digits (not compulsory) following its barcode message. The two digits verify the barcode message. "NO Check, Transmit All" means to read without check and transmit » all bytes including barcode message and Check Digits.
Page 85: Ucc/Ean-128
Symbols UCC/EAN-128 Tools Code Programming ON Load Factory Default ** Load UCC/EAN-128 Factory Default 【Pro CMD：0412000】 Code Programming OFF Enable/Disable UCC/EAN-128 ** Enable UCC/EAN-128 【Pro CMD：0412020】 Disable UCC/EAN-128 【Pro CMD：0412010】 When the engine can not read UCC/EAN-128, please read “Enable UCC/EAN-128” and try again.
Page 86: Gs1 Databar
Symbols GS1 Databar Tools Code Programming ON Load Factory Default Code Programming OFF ** Load GS1 Databar Factory Default 【Pro CMD：0413000】 Enable/Disable GS1 Databar ** Enable GS1 Databar 【Pro CMD：0413020】 Disable GS1 Databar 【Pro CMD：0413010】 When the engine can not read GS1 Databar, please read “Enable GS1 Databar” and try again.
Page 87: Ean·ucc Composite
Symbols EAN·UCC Composite Tools Code Programming ON Load Factory Default Code Programming OFF ** Load EAN·UCC Composite Factory Default 【Pro CMD：0414000】 Enable/Disable EAN·UCC Composite Enable EAN·UCC Composite 【Pro CMD：0414020】 ** Disable EAN·UCC Composite 【Pro CMD：0414010】 Enable UPC/EAN Composite 【Pro CMD：0414040】 ** Disable UPC/EAN Composite 【Pro CMD：0414030】...
Page 88: Code 11
Symbols Code 11 Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Code 11 Factory Default 【Pro CMD：0415000】 Enable/Disable Code 11 Enable Code 11 【Pro CMD：0415020】 ** Disable Code 11 【Pro CMD：0415010】 When the engine can not read Code 11, please read “Enable Code 11” and try again. Page 82...
Page 89: Select Message Length
Symbols Code 11 Tools Code Programming ON Select Message Length It is used to program the valid reading length of Code 11. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
Page 90: Check Digit
Symbols Code 11 Tools Code Programming ON Check Digit Code 11 may include Check Digit (not compulsory) following its barcode message. It veriﬁes the barcode message. "NO Check, Transmit All" means to read without check and transmit all » bytes including barcode message and Check Digit. Code Programming OFF "Check, Do Not Transmit Check Digit"...
Page 91: Isbn
Symbols ISBN Tools Code Programming ON Load Factory Default Code Programming OFF ** Load ISBN Factory Default 【Pro CMD：0416000】 Enable/Disable ISBN Enable ISBN 【Pro CMD：0416020】 ** Disable ISBN 【Pro CMD：0416010】 When the engine can not read ISBN, please read “Enable ISBN” and try again. Transmit ** Transmit 13 digits 【Pro CMD：0416030】...
Page 92: Industrial 25
Symbols Industrial 25 Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Industrial 25 Factory Default 【Pro CMD：0417000】 Enable/Disable Industrial 25 Enable Industrial 25 【Pro CMD：0417020】 ** Disable Industrial 25 【Pro CMD：0417010】 When the engine can not read Industrial 25, please read “Enable Industrial 25” and try again.
Page 93: Select Message Length
Symbols Industrial 25 Tools Code Programming ON Select Message Length It is used to program the valid reading length of Industrial 25. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Industrial 25 Message Length is deﬁned by “Min.
Page 94: Check Digit
Symbols Industrial 25 Tools Code Programming ON Check Digit Industrial 25 may include Check Digit (not compulsory) following its barcode message. It veriﬁes the barcode message. "NO Check, Transmit All" means to read without check and transmit all » bytes including barcode message and Check Digit. Code Programming OFF "Check, Do Not Transmit Check Digit"...
Page 95: Standard 25
Symbols Standard 25 Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Standard 25 Factory Default Pro CMD 【：0418000】 Enable/Disable Standard 25 Enable Standard 25 【Pro CMD：0418020】 ** Disable Standard 25 【Pro CMD：0418010】 When the engine can not read Standard 25, please read “Enable Standard 25” and try again.
Page 96: Select Message Length
Symbols Standard 25 Tools Code Programming ON Select Message Length It is used to program the valid reading length of Standard 25. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Standard 25 Message Length is deﬁned by “Min.
Page 97: Check Digit
Symbols Standard 25 Tools Code Programming ON Check Digit Standard 25 may include Check Digit (not compulsory) following its barcode message. It veriﬁes the barcode message. "NO Check, Transmit All" means to read without check and transmit all » bytes including barcode message and Check Digit. Code Programming OFF "Check, Do Not Transmit Check Digit"...
Page 98: Plessey
Symbols Plessey Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Plessey Factory Default Pro CMD 【：0419000】 Enable/Disable Plessey Enable Plessey 【Pro CMD：0419020】 ** Disable Plessey 【Pro CMD：0419010】 When the engine can not read Plessey, please read “Enable Plessey” and try again. Page 92...
Page 99: Select Message Length
Symbols Plessey Tools Code Programming ON Select Message Length It is used to program the valid reading length of Plessey. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Plessey Message Length is deﬁned by “Min.
Page 100: Check Digit
Symbols Plessey Tools Code Programming ON Check Digit Plessey may include Check Digits (not compulsory) following its barcode message. The two digits verify the barcode message. "NO Check, Transmit All" means to read without check and transmit all » bytes including barcode message and Check Digits. Code Programming OFF "Check, Do Not Transmit Check Digit"...
Page 101: Msi-Plessey
Symbols MSI-Plessey Tools Code Programming ON Load Factory Default Code Programming OFF ** Load MSI-Plessey Factory Default Pro CMD 【：0420000】 Enable/Disable MSI-Plessey Enable MSI-Plessey 【Pro CMD：0420020】 ** Disable MSI-Plessey 【Pro CMD：0420010】 When the engine can not read MSI-Plessey, please read “Enable MSI-Plessey” and try again.
Page 102: Select Message Length
Symbols MSI-Plessey Tools Code Programming ON Select Message Length It is used to program the valid reading length of MSI-Plessey. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Code Programming OFF MSI-Plessey Message Length is deﬁned by “Min.
Page 103: Check Digit
Symbols MSI-Plessey Tools Code Programming ON Check Digit Plessey may include Check Digits(s) (not compulsory) following its barcode message. It may have one or two digits, which verify the barcode message. "NO Check, Transmit All" means to read without check and transmit all »...
Page 104: Pdf417
Symbols PDF417 Tools Code Programming ON Load Factory Default Code Programming OFF ** Load PDF417 Factory 【Pro CMD：0501000】 Enable/Disable PDF417 ** Enable PDF417 【Pro CMD：0501020】 Disable PDF417 【Pro CMD：0501010】 When the engine can not read PDF417, please read “Enable PDF417” and try again. Page 98...
Page 105: Select Message Length
Symbols PDF417 Tools Code Programming ON Select Message Length It is used to program the valid reading length of PDF417. The engine will not send barcode message to the Host, if the decoded data length does not match the valid reading length.
Page 106: Pdf417 Twin Code
Symbols PDF417 Tools Code Programming ON PDF417 Twin Code PDF417 twin code is 2 PDF417 barcodes paralleled vertically or horizontally. They must have the same direction. Their speciﬁcations must be similar and the distance between them must be short. There are 3 options for reading PDF417 twin code: Code Programming OFF Single PDF417 Only: Read either PDF417 code.
Page 107: Qr Code
Symbols QR Code Tools Code Programming ON Load Factory Default Code Programming OFF ** Load QR Code Factory Default 【Pro CMD：0502000】 Enable/Disable QR Code ** Enable QR Code 【Pro CMD：0502020】 Disable QR Code 【Pro CMD：0502010】 When the engine can not read QR Code, please read “Enable QR Code” and try again. Page 101...
Page 108: Select Message Length
Symbols QR Code Tools Code Programming ON Select Message Length It is used to program the valid reading length of QR Code. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
Page 109: Qr Twin Code
Symbols QR Code Tools Code Programming ON QR Twin Code QR twin code is 2 QR barcodes paralleled vertically or horizontally.They must have the same direction. Their speciﬁcations must be similar and the distance between them must be short. There are 3 options for reading QR twin code: Code Programming OFF Single QR Only: Read either QR code.
Page 110: Aztec
Symbols Aztec Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Aztec Factory Default 【Pro CMD：0503000】 Enable/Disable Aztec Enable Aztec 【Pro CMD：0503020】 ** Disable Aztec 【Pro CMD：0503010】 When the engine can not read Aztec, please read “Enable Aztec” and try again. Page 104...
Page 111: Select Message Length
Symbols Aztec Tools Code Programming ON Select Message Length It is used to program the valid reading length of Aztec. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
Page 112: Reading Multi-Barcodes Of An Image
Symbols Aztec Tools Code Programming ON Reading Multi-barcodes of an Image There are three modes: Mode 1：Read one barcode only. » Code Programming OFF Mode 2：Read ﬁxed number of barcodes only. » Mode 3：Composite Reading. Read ﬁxed number of barcodes ﬁrst, if failed, »...
Page 113: The Number Of Multi-Barcodes
Symbols Aztec Tools Code Programming ON The number of Multi-barcodes Code Programming OFF ** 1 【Pro CMD：0503060】【Pro CMD：0503064】【Pro CMD：0503061】【Pro CMD：0503065】【Pro CMD：0503062】【Pro CMD：0503066】【Pro CMD：0503063】【Pro CMD：0503067】 Page 107...
Page 114: Data Matrix
Symbols Data Matrix Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Data Matrix Factory Default 【Pro CMD：0504000】 Enable/Disable Data Matrix ** Enable Data Matrix 【Pro CMD：0504020】 Disable Data Matrix 【Pro CMD：0504010】 When the engine can not read Data Matrix, please read “Enable Data Matrix” and try again.
Page 115: Select Message Length
Symbols Data Matrix Tools Code Programming ON Select Message Length It is used to program the valid reading length of Data Matrix. The engine will not send barcode message to the Host, if the decoded data length does not match the valid reading length.
Page 116: Data Matrix Twin Code
Symbols Data Matrix Tools Code Programming ON Data Matrix Twin Code Data Matrix twin code is 2 Data Matrix barcodes paralleled vertically or horizontally.They must have the same direction. Their speciﬁcations must be similar and the distance between them must be short. Code Programming OFF There are 3 options for reading Data Matrix: Single Data Matrix Only: Read either Data Matrix.
Page 117: Rectangular Symbols
Symbols Data Matrix Tools Code Programming ON Rectangular Symbols Data Matrix has two formats: Square symbols, which has the same amount of models in length and » Code Programming OFF width： 10*10，12*12..144*144。 Rectangular symbols, which has different amounts of models in length and »...
Page 118: Maxicode
Symbols Maxicode Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Maxicode Factory Default 【Pro CMD：0505000】 Enable/Disable Maxicode Enable Maxicode 【Pro CMD：0505020】 ** Disable Maxicode 【Pro CMD：0505010】 When the engine can not read Maxicode, please read “Enable Maxicode” and try again. Page 112...
Page 119: Select Message Length
Symbols Maxicode Tools Code Programming ON Select Message Length It is used to program the valid reading length of Maxicode. The engine will not send barcode message to the Host, if the decoded data length does not match the valid reading length.
Page 120: Chinese Sensible Code
Symbols Chinese Sensible Code Tools Code Programming ON Load Factory Default Code Programming OFF ** Load Chinese Sensible Code Factory Default 【Pro CMD：0508000】 Enable/Disable Chinese Sensible Code Enable Chinese Sensible Code 【Pro CMD：0508020】 ** Disable Chinese Sensible Code 【Pro CMD：0508010】 When the engine can not read Maxicode, please read “Enable Chinese Sensible Code”...
Page 121: Select Message Length
Symbols Chinese Sensible Code Tools Code Programming ON Select Message Length It is used to program the valid reading length of Chinese Sensible Code. The engine will not send barcode message to the Host, if the decoded data length does not match the valid reading length.
Page 122: Ocr
Introduction OCR (Optical Character Recognition) is the technology that captures image of printed information, and recognizes the image to editable characters. The engine supports OCR B standard and specific typefaces, such as: ■ 0 1 2 3 4 5 6 7 8 ■...
Page 123: Preﬁx/Sufﬁx
Prefix/Suffix Introduction 1D barcodes could contain digits, letters and symbols, etc. 2D barcodes could contain more data, such as Chinese characters and other multi-byte characters. However, in reality, they do not and should not have all the information we need, such as barcode type, date and time of scan, delimiter, and so on, in order to keep the code short and ﬂexible.
Page 124: General Programming
Preﬁx/Sufﬁx Preﬁx/Sufﬁx General Programming Tools Code Programming ON Disable or Enable Prefix/Suffix Disable All Preﬁx/Sufﬁx: Transmit barcode message with no Preﬁx/Sufﬁx. Enable All Preﬁx/Sufﬁx: Allow appending Code ID preﬁx, AIM preﬁx, User Code Programming OFF preﬁx, User sufﬁx and Terminal to the barcode message. ** Disable All Preﬁx/Sufﬁx 【Pro CMD：0311000】...
Page 125: Preﬁx Sequences
Preﬁx/Sufﬁx Preﬁx/Sufﬁx General Programming Tools Code Programming ON Prefix Sequences 6 options of Preﬁx Sequences: Code Programming OFF ** CodeID + AIM + User Preﬁx 【Pro CMD：0317000】 AIM + User Preﬁx + CodeID 【Pro CMD：0317030】 CodeID + User Preﬁx + AIM 【Pro CMD：0317010】...
Page 126: Disable Or Enable User Preﬁx
Preﬁx/Sufﬁx Preﬁx/Sufﬁx General Programming Tools Code Programming ON Disable or Enable User Preﬁx User Preﬁx is added before barcode message. For example, if the user preﬁx is “AB” and the barcode message is “123”, the Host receives “AB123”. Code Programming OFF ** Disable User Preﬁx 【Pro CMD：0305000】...
Page 127: Aim Preﬁx
Preﬁx/Sufﬁx Preﬁx/Sufﬁx AIM Preﬁx Tools Code Programming ON AIM (Automatic Identiﬁcation Manufactures) deﬁnes AIM preﬁx for many standard barcode formats. AIM Preﬁx Format: “]” + AIM preﬁx + “0” Code Programming OFF ** Disable AIM Preﬁx for All Barcodes 【Pro CMD：0308000】 Enable AIM Preﬁx for All Barcodes 【Pro CMD：0308030】...
Page 128: Code Id Preﬁx
Preﬁx/Sufﬁx Preﬁx/Sufﬁx Code ID Preﬁx Tools Code Programming ON Besides AIM preﬁx, Code ID preﬁx can be used to denote barcode format and can be customized. The Code ID preﬁx MUST be one (1) or two (2) visible English letters. Code Programming OFF ** No Code ID Preﬁx 【Pro CMD：0307000】...
Page 129: Modify Code Id
Preﬁx/Sufﬁx Preﬁx/Sufﬁx Code ID Preﬁx Tools Code Programming ON Modify Code ID See the examples below for how to modify a code ID and restore factory default code ID. Modify PDF417 Code ID to be “p” (hex value is 0x70) Code Programming OFF 1.
Page 130 Preﬁx/Sufﬁx Preﬁx/Sufﬁx Code ID Preﬁx Tools Code Programming ON Modify EAN-8 【Pro CMD：0004040】 Code Programming OFF Modify EAN-13 【Pro CMD：0004050】 Modify ITF-6 【Pro CMD：0004100】 Modify UPC-E 【Pro CMD：0004060】 Modify Code 39 【Pro CMD：0004130】 Modify UPC-A 【Pro CMD：0004070】 Modify Codabar 【Pro CMD：0004150】 Modify Interleaved 2 of 5 【Pro CMD：0004080】...
Page 131 Preﬁx/Sufﬁx Preﬁx/Sufﬁx Code ID Preﬁx Tools Code Programming ON Modify Code 128 【Pro CMD：0004020】 Code Programming OFF Modify ISBN 【Pro CMD：0004240】 Modify UCC/EAN-128 【Pro CMD：0004030】 Modify Industrial 25 【Pro CMD：0004250】 Modify Code 11 【Pro CMD：0004280】 Modify Standard 25 【Pro CMD：0004260】 Modify EAN•UCC Composite 【Pro CMD：0004300】...
Page 132: User Sufﬁx
Preﬁx/Sufﬁx Preﬁx/Sufﬁx User Sufﬁx Tools Code Programming ON Disable or Enable User Sufﬁx User sufﬁx is appended to the right of barcode message. For example, if user sufﬁx is “AB”, and the barcode message is “123”, The Host receives “123AB”. Code Programming OFF **Disable User Sufﬁx 【Pro CMD：0306000】...
Page 133: Terminal
Preﬁx/Sufﬁx Preﬁx/Sufﬁx Terminal Tools Code Programming ON Disable or Enable Terminal “Terminal” is the termination for a string of barcode messages. It can not be formatted like other sufﬁx and preﬁx. It is ﬁxed to the right and the very end of a barcode transmission.
Page 134: Message Interception & Pack
Message Interception & Pack Introduction Barcode message could divide information into different sections, such as product ID, manufacture ID, and so on. They are important overall. However, at certain situations, some of them are not of interest. This is where message interception comes in. Message interception feature allows transmission of selected section(s).
Page 135: Message Interception
Message Interception & Pack Message Interception & Pack Message Interception Tools Code Programming ON Interception Rule No.1: It only intercepts selected symbols’ raw barcode messages and it effects all barcodes of the barcode format. Interception Rule No.2: There are maximum 3 interception options restored in the non-volatile memory.
Page 136: Programming 1D Intercept Option
Message Interception & Pack Message Interception & Pack Message Interception Tools Code Programming ON Programming 1D Intercept Option When programming 1D intercept option, read digit codes as interception command. The rules is as below： The interception command format of 1D interception command regards »...
Page 137: Programming 2D Intercept Option
Message Interception & Pack Message Interception & Pack General Programming Tools Code Programming ON Programming 2D Intercept Option When programming 2D intercept option, read digit codes as interception command. The rules is as below： The interception command has two parts, which are barcode type »...
Page 138: Message Pack
Message Interception & Pack Message Interception & Pack Message Pack Tools Code Programming ON Introduction Data Pack is for the special requirements of barcode message. There are 3 types of data pack. Data pack effects all data formats, in that be sure to load the default “Disable Pack”...
Page 139: Batch Programming
Batch Programming Tools Introduction Code Programming ON Batch Programming can integrate a programming sequence into one barcode. Batch Programming Rules: 1、 Sub-command is in this format: Programming Command + Parameters 2、 Sub-commands are terminated by semicolons. Note that there is no blank between a sub-command and its terminator semicolon.
Page 140: How To Build A Batch Command
Batch Programming How to build a batch command Batch command can contain many commands. Each command is divided by semicolon. Batch command must be ended with save command. Command structure: command (+ equal mark + setting information) The setting command list is provided below There are 4 setting command modes 1、...
Page 141: Produce Setting Code
Batch Programming Produce setting code Make the command list (ended with save command) to a PDF417, QR code or DataMatrix. For example, to produce a batch command means: light Always On, Auto Scan, change delay time to 2 seconds, Disable Fixed Length of I 2 of 5. Firstly ﬁnd commands as follows 0200030;（light Always On）...
Page 142: Use Batch Setting Code
Batch Programming Batch Programming Use batch setting code Tools Code Programming ON Read “Code Programming ON”, then read “enable batch setting code”, and then read the batch setting code produced just now, ﬁnally Read “Code Programming Off” Code Programming OFF Code Programming ON 【Pro CMD：0006010】...
Page 143: Appendix
Appendix Digit Code It is must to be read save after read digit code. 【Pro CMD：0000000】【Pro CMD：0000040】【Pro CMD：0000010】【Pro CMD：0000050】【Pro CMD：0000020】【Pro CMD：0000060】【Pro CMD：0000030】【Pro CMD：0000070】 Page 137...
Page 144 Appendix Digit Code 【Pro CMD：0000080】【Pro CMD：0000120】【Pro CMD：0000090】【Pro CMD：0000130】【Pro CMD：0000100】【Pro CMD：0000140】【Pro CMD：0000110】【Pro CMD：0000150】 Page 138...
Page 145: Save And Abort
Appendix Appendix Save and Abort Tools Code Programming ON In order to save the received data “Save” has to be read after data transition completed. If error occurs when reading data, the wrong data can be deleted and the setting up can be done again.. Eg, after a program code is received then ‘1 2 3”...
Page 146: Factory Default List
Appendix Factory Default List Parameters Factory Default Remark General Programming Code Programming Send Pro Code Value Illumination Illumination Wink Aiming Aiming Wink Decoding Beep Decoding Beep Type Type 1 Decoding Beep Volume Loud Power On Beep Working Mode Auto Mode One Reading Timeout 3000ms Multi-reading Semi-prohibit,...
Page 147 Appendix Factory Default List Parameters Factory Default Remark Symbol Code 128 Enable Max Message Length Min Message Length EAN-8 Enable Send Check Digit Enable 2 Digits Addenda Code Enable 5 Digits Addenda Code Expand to EAN-13 EAN-13 Enable Send Check Digit Enable 2 Digits Addenda Code Enable 5 Digits Addenda Code UPC-E...
Page 148 Appendix Factory Default List Min Message Length No less than 4 Specified Lengths ITF-6 Enable ITF-14 Enable Matrix 2 of 5 Enable Check Send Check Digit Max Message Length Min Message Length No less than 4 Code 39 Enable Check Send Start &...
Page 149 Appendix Factory Default List EAN•UCC Composite Enable UPC/EAN Composite Enable Code 11 Enable Send Check Digit １Digit, MOD11 Check Max Message Length Min Message Length No less than 4 ISBN Enable Transmit 13 Digits Industrial 25 Enable Check Max Message Length Min Message Length No less than 4 Standard 25...
Page 150 Appendix Factory Default List PDF417 Enable Read Single PDF417 Only Max Message Length 2710 Min Message Length Read Forward Direction Barcode Only QR Code Enable Read Single QR Only Max Message Length 7089 Min Message Length Aztec Enable Max Message Length 3832 Min Message Length Reading Multi-barcodes of an Image...
Page 151: Aim Id List
Appendix AIM ID List Symbol AIM ID Possible AIM ID Modiﬁers(m) Code 128 UCC/EAN-128 EAN-8 EAN-13 EAN-13 with Addon UPC-E UPC-E with Addon UPC-A UPC-A with Addon 0,1,3 Interleaved 2 of 5 ITF-6 ITF-14 Matrix 2 of 5 Code 39 0,1,3,4,5,7 Codabar 0,2,4...
Page 152: Code Id List
Appendix Code ID List Symbol Code ID Code 128 UCC/EAN-128 EAN-8 EAN-13 UPC-E UPC-A Interleaved 2 of 5 ITF-6 ITF-14 Matrix 2 of 5 Code 39 Codabar Code 93 Code 11 GS1 Databar EAN•UCC Composite ISBN Industrial 25 Standard 25 Plessey MSI-Plessey PDF417...
Page 153: Symbols Id Number
Appendix Symbols ID Number Symbol ID Number Code 128 UCC/EAN-128 EAN-8 EAN-13 UPC-E UPC-A Interleaved 2 of 5 ITF-14 ITF-6 Matrix 2 of 5 Code 39 Codabar Code 93 ISBN Industrial25 Standard25 Plessey Code11 MSI-Plessey EAN•UCC Composite GS1 Databar PDF417 QR Code Aztec DataMatrix...
Page 154 Appendix ASCII Table Char NUL (Null char.) SOH (Start of Header) STX (Start of Text) ETX (End of Text) EOT (End of Transmission) ENQ (Enquiry) ACK (Acknowledgment) BEL (Bell) BS (Backspace) HT (Horizontal Tab) LF (Line Feed) VT (Vertical Tab) FF (Form Feed) CR (Carriage Return) SO (Shift Out)
Page 155 Appendix ASCII Table Char - (Minus / Dash) (Dot) (Forward Slash) (Colon) (Semi-colon) < (Less Than) (Equal Sign) > (Greater Than) (Question Mark) @ (AT Symbol) Page 149...
Page 156 Appendix ASCII Table Char - (Minus / Dash) (Dot) (Forward Slash) (Colon) (Semi-colon) < (Less Than) (Equal Sign) > (Greater Than) (Question Mark) @ (AT Symbol) Page 150...
Page 157 ID TECH 10721 Walker Street Cypress, CA 90630 (714) 761-6368 www.idtechproducts.com. 80108506-001 rev.B...

IDTECH 2DScan FX100 User Manual

About this Guide

Getting to Start

Programming the Engine

RS232 Interface

USB Interface

Symbols

Ocr

PreﬁX/SufﬁX

Message Interception & Pack

Batch Programming

Appendix

Quick Links

Related Manuals for IDTECH 2DScan FX100

Summary of Contents for IDTECH 2DScan FX100