Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for IDTECH BluScan
Summary of Contents for IDTECH BluScan
- Page 1 BluScan Barcode Scanner Quick Start Manual Default Check Version...
-
Page 2: Fcc Warning Statement
FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 3: Limited Warranty
ID TECH is a registered trademark of International Technologies & Systems Corporation. BluScan and Value through Innovation are trademarks of International Technologies & Systems Corporation... - Page 4 Range Cordless Imager provides a high performance scanning with a rapid scan rate (450 scans/sec) and superior depth of field (up to 40 inches on 40-mil codes). Utilizing IDTECH’s unique wireless-communication technology, the BluScan operates with a 100-meter data transmission range.
- Page 5 Section 2 INSTALLATION AND OPERATION Installation- Keyboard Wedge First of all, you must switch off power for the terminal/computer. Disconnect the keyboard cable from the back of the terminal/computer and connect to the interface cable of the scanner. Connect the interface cable of the scanner to the terminal/computer. Turn the terminal/computer power on.
-
Page 6: Pin Assignments
Pin Assignments Keyboard Wedge Connector (To Host Side): Mini-DIN 6P Male Mini-DIN 6P Female DATA / PC CLK / KB DATA / KB VCC (+5V) VCC (+5V) CLK / PC Mini-DIN 6P Female Connector Mini-DIN 6P Male Connector RS-232 DB-9F Connector (To Host Side): Definition VCC (+5V) -
Page 7: Troubleshooting
Section 3 TROUBLESHOOTING Troubleshooting assistance for common problems: The data from the Scanner is not as expected. ANS: Please read User’s Manual and follows up all instruction The Scanner does not output data. . ANS:Check basic operation: well connect the cable; examine that if the barcode type is enabled. -
Page 8: Specification
Section 4 SPECIFICATION BluScan Specification Operational Light Source 630 nm Visible Red LED Optical System 2048 pixel CCD (Charge-coupled device) Depth of Scan Up to 600mm (CODE 39, PSC=90%, 20mils) Field Scanning Width 160mm Scan Speed 450 scans/sec 0.1mm (4mils) Code39,PCS=90%... - Page 9 Operating (Cradle) Power – Standby 400 mW (Cradle) Current – 110 mA Operating (Cradle) Current – 80 mA Standby (Cradle) Charge Current 510 mA (Cradle) Input Voltage 3.4V ~ 4.2V (Imager) Power - Operating 851 mW (Imager) Power – Standby 67 mW (Imager) Current –...
- Page 10 Keyboard emulation type (intermessage delay, keyboard type and keyboard language) Serial interface type (ACK/NAK, Xon/Xoff, RTS/CTS, good read LED control, start/stop bits) Remark. Current are marked as RMS (Root mean square) Indications of BluScan Status Green LED Red LED Orange LED...
-
Page 11: Default Setting
Section 5 READING MODE SETTINGS Default setting For each barcode shown as below: V = Enabled as default setting - = Not supported Empty space = Download User’s Manual ; Please visit IDTECH website : www.idtechproducts.com Checksum Checksum Read Transmissi Code... -
Page 12: Testing Codes
Section 6 TESTING CODES Code 128 UCC/EAN-128 UPC-E UPC-A Interleaved 2 of 5 Code 39 Full User’s Manual is available for download on www.idtechproducts.com... - Page 13 ID TECH 10721 Walker Street Cypress, CA 90630 (714) 761-6368 www.idtechproducts.com 80106501-001 rev.A...