Table of Contents
Advertisement
Chameleon QBar Pro
Program Mode:
1. Plug the fixture in and press the MODE button until "PROG PRO:
XX" is displayed.
2. Use the UP or DOWN buttons to scroll through the 20 programs.
Once you have found your desired program press the SET UP
button to adjust the program speed.
3. "SPEED:XX" will be displayed. Use the UP or DOWN button to
adjust the speed between "01" (slowest) and "16" (fastest). Once
you have set your desired running speed, press the SET UP but-
ton to to enter the the strobe mode.
4. "FLASH: XX" will be displayed, this is strobe mode. The strobe
can be adjusted between "00" (flash off) to "15" (fastest flash).
WiFLY Address:
This function is used to set the WiFly address. This address must
match the address that is set to WiFly TransCeiver or WiFly controller.
See page 14 for WiFly Set Up.
1. Plug the fixture in and press the MODE button until "WIFI SETT
ADDR: XX" is displayed. "XX" represents the current WiFly
address setting, which is a number between 00-14.
2. Use the UP or DOWN buttons to find your desired address. Then
press the SET UP button to activate WiFly control.
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
Color Balance Mode:
1. Plug the fixture in and press the MODE button until "BALANCE" is
displayed. Press the SET UP button for at lease 3 seconds until
the displayed number begins to flash.
2. When "RED" is displayed you are in Red balance mode. Press the
UP and DOWN buttons to adjust intensity.
3. When "GREN" is displayed you are in Green balance mode.
Press the UP and DOWN buttons to adjust intensity.
4. When "BLUE" is displayed you are in Blue balance mode. Press
the UP and DOWN buttons to adjust intensity.
5. When "AMBE" is displayed you are in Amber balance mode.
Press the UP and DOWN buttons to adjust intensity.
6. Press the SET UP button for 3 seconds to save your settings.
ADJ Products, LLC - www.adj.com - Chameleon QBar Pro User Manual Page 10
Operating Instructions
Chameleon QBar Pro
Activate IR Sensor:
This function is used to activate and deactivate the infared sen-
sor. When this function is activated you can control the fixture using
the ADJ LED RC2 (sold separately), UC IR (sold separately), and
Airstream IR app. Please see pages 13-15 for remote controls and
functions. To control the Chameleon QBar Pro Pro, plug the included
IR receiver into IR receiver input located on the rear of the controller.
You must aim the remote at the IR sensor and be no more the 30 feet
away.
1. Plug the fixture in and press the MODE button until "OTHER" is
displayed.
2. Press the SET UP button until "IR: XX" is displayed. "XX" repre-
sents either "ON" or "OFF".
3. Use the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
DMX State:
This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the fixture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to
when power is applied.
1. Plug the fixture in and press the MODE button until "DMX MODE
ADDR:XXX" is displayed.
2. Press the SET UP button until "DMX MODE NO" is displayed. The
current DMX state will be displayed.
• "BLACK" (Blackout) - If the DMX signal is lost or interrupted,
the unit will automatically go into stand by mode.
• "HOLD" (Last State) - If the DMX signal is lost or interrupted,
the fixture will stay in the last DMX set up.
• "AUTO" (Auto Run) - If the DMX signal is lost or interrupted,
the unit will automatically go into Auto Run mode.
3. Press the UP or DOWN buttons to scroll through and select
your desired DMX state.
ADJ Products, LLC - www.adj.com - Chameleon QBar Pro User Manual Page 11
Operating Instructions
Advertisement
Table of Contents
