Table of Contents
Advertisement
Chameleon QBar Pro
DMX address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 4 Channel Mode, press the MODE button until
"CHAN:4" is displayed. This is the 4 Channel DMX Mode.
• To run the 5 Channel Mode, press the MODE button until
"CHAN:5" is displayed. This is the 5 Channel DMX Mode.
• To run the 7 Channel Mode, press the MODE button until
"CHAN:7" is displayed. This is the 7 Channel DMX Mode.
• To run the 9 Channel Mode, press the MODE button until
"CHAN:9" is displayed. This is the 9 Channel DMX Mode.
• To run the 10 Channel Mode, press the MODE button until
"CHAN:10" is displayed. This is the 10 Channel DMX Mode.
• To run the 12 Channel Mode, press the MODE button until
"CHAN:12" is displayed. This is the 12 Channel DMX Mode.
• To run the 14 Channel Mode, press the MODE button until
"CHAN:14" is displayed. This is the 14 Channel DMX Mode.
4. Please see pages 18-25 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX controller.
RGBA Dimmer Mode:
1. Plug the fixture in and press the MODE button until "MANUAL" is
displayed.
2. When "RED: XXX" is displayed you are in Red dimming mode.
Press the UP and DOWN buttons to adjust intensity. After you
have finished adjusting the intensity, or if you would like to skip to
the next color, press the SET UP button.
3. When "GREN: XXX" is displayed you are in Green dimming
mode. Press the UP and DOWN buttons to adjust intensity.
4. When "BLUE: XXX" is displayed you are in Blue dimming mode.
Press the UP and DOWN buttons to adjust intensity.
5. When "AMBE: XXX" (Amber) is displayed you are in Amber dim-
ming mode. Press the UP and DOWN buttons to adjust intensity.
6. After you have adjusted the colors to make your desired color
you can then activate strobing by pressing the SET UP button to
enter the strobe mode.
ADJ Products, LLC - www.adj.com - Chameleon QBar Pro User Manual Page 8
Operating Instructions
Chameleon QBar Pro
7. "FLASH: XX" will be displayed, this is strobe mode. The strobe
can be adjusted between "00" (flash off) to "15" (fastest flash).
Sound Active Mode:
In this mode the Chameleon QBar Pro will react to sound, and chase
through the different colors.
1. Plug the fixture in and press the MODE button until "SOUND
PRO:XX" is displayed. "XX" represents the current sound active
mode. There 16 modes to choose from.
2. Use the UP or DOWN buttons to find your desired sound active
mode. After you have found your desired mode, press the SET UP
button to enter sound sensitivity adjustment.
3. "SENS:XX" will now be displayed. Use the UP or DOWN buttons
to adjust the sound sensitivity. "01 is the least sensitive, and "08"
is the most sensitive.
Auto Run Mode:
1. Plug the fixture in and press the MODE button until "AUTO RUN
SPEED: XX" is displayed. "XX" represents the current speed set-
ting.
2. Use the UP or DOWN button to adjust the speed between
"01" (slowest) and "16" (fastest). Once you have set your desired
running speed, press the SET UP button to enter the strobe mode.
3. "FLASH: XX" will be displayed, this is strobe mode. The strobe
can be adjusted between "00" (flash off) to "15" (fastest flash).
Use the UP or DOWN button to adjust the strobe speed.
Static Color Mode:
1. Plug the fixture in and press the MODE button until "CLR MACS
COLOR:XX" is displayed. "XX" represents the current displayed
color
2. There are 64 colors to choose from. Use the UP and DOWN but-
tons to scroll through the 64 colors. After you have found your
desired color you can activate strobing by pressing the SET UP
button to enter the strobe mode.
3. "FLASH:XX" will be displayed, this is strobe mode. The strobing
can be adjusted between "00" (flash off) to "15" (fastest flash).
ADJ Products, LLC - www.adj.com - Chameleon QBar Pro User Manual Page 9
Operating Instructions
Advertisement
Table of Contents
