Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Related Manuals for ROBBE blue arrow 1.0 3D
Summary of Contents for ROBBE blue arrow 1.0 3D
- Page 1 Operating Instructions BLUE ARROW 1.0 3D 2.4 GHz No. S2523...
- Page 2 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523...
- Page 3 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Explanation of specialist terms: Contents Page No. Climb and descent ("collective pitch / throttle"): Explanation of specialist terms / Contents This controls the model's climb and descent. Safety Notes...
-
Page 4: Mode
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Do not stand close to the hazard area around rotating parts when Be sure to read right through these Safety Notes before you build your model. Always keep to the procedures and settings recom- an electric motor is connected to the flight battery. - Page 5 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Use only those components and accessories which we specifically re- Liability Exclusion commend. robbe Modellsport is unable to ensure that you observe the assembly and operating instructions, or the conditions and methods used for installing, Do not carry out modifications to the radio control system components operating and maintaining the model components.
-
Page 6: Safety Notes
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Dear Customer, Congratulations on choosing a factory-assem- bled model helicopter from our range. Many thanks for placing your trust in us. The model can be completed and made ready to fly very quickly. - Page 7 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Transmitter description* (Mode 1) - The mode select switch** is located on the back of the transmitter (*Complete operating instructions for the J6 transmitter can be found in the Download area at www.robbe.com) Aerial...
- Page 8 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Transmitter description* (Mode 2) - The mode select switch** is located on the back of the transmitter (*Complete operating instructions for the J6 transmitter can be found in the Download area at www.robbe.com) Aerial...
- Page 9 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Transmitter LCD display Collective pitch and throttle adjustment (default settings) Normal flight Mode display Transmitter voltage display Collective Screen Throttle pitch Channel reverse Gyro Collective pitch gain display Throttle curve normal...
- Page 10 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Motor connections Flybarless check before the first flight Throttle Tail rotor motor Tail rotor Pitch-axis Main motor Roll...
-
Page 11: Safety Notes
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Charging the flight battery Safety Notes regarding LiPo batteries: • Do not place the battery in water or any other liquid. • Do not heat or incinerate the battery; do not place it Connect the battery charger to the in a microwave oven. mains PSU, and plug the PSU into a • Avoid short-circuits, and never charge the battery with... -
Page 12: Flight Preparation
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Flight preparation Open the battery compartment and insert dry or rechargeable cells. Close the battery compartment. Move all the switches to the forward position, and switch the transmitter on (Fig. 1). If switch "A" or "B" is at the "ON" position, the screen will flash, and you will hear a "beep". - Page 13 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Flight preparation Check the correct position of the swashplate before the first flight. The swashplate must sit exactly horizontal when viewed from the side and front of the model. Position the model on a totally flat surface. Now move the throttle stick to the lowest throttle position, and switch the transmitter on.
- Page 14 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Trim adjustments, Mode 1 Trim adjustments, Mode 2 Throttle trim: Throttle trim: If the rotor starts to move without the If the rotor starts to move without the throttle stick being touched, or does not...
-
Page 15: Controlling The Model
Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Controlling the model in Mode 1 Controlling the model in Mode 2 Lift off: Landing: Lift off: Landing: Yaw left: Yaw right: Yaw left: Yaw right: Pitch forward: Pitch back:... - Page 16 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Important Notes The first few flights Take-off: use the 3D switch for aerobatics only. To take off, slow- Ideally the first flight should take place in a large indoor space devoid ly and steadily increase rotor speed until the model is hovering of obstructions.
- Page 17 Operating Instructions, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523...
-
Page 18: Replacement Parts
Replacement parts list, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 NE250230 S2523001 S2523002 NE250903 NE250904 NE250905 NE250906 NE250907 NE250908 NE250909 NE250910 NE250911 NE250912 NE250913 NE250914 NE250915 NE250916 NE250917 NE250918 NE250919... -
Page 19: Replacement Parts
Replacement parts list, BLUE ARROW 1.0 3D RTF 2.4 GHz No. S2523 Replacement parts list, BLUE ARROW 1.0 3D RTF Order No. Description NE250230 Mains PSU and battery charger S2523001 Canopy S2523002 Rotor blades NE250903 Main rotor blade holder NE250904... - Page 20 Modellsport Beteiligungs GmbH Gießen / HRB 5793 · Managing Directors: G. Geiger, E. Dörr Errors and technical modifications reserved. · Copyright robbe-Modellsport 2011 Duplication and copying of the text, in whole or in part, is only permitted with the prior written approval of robbe-Modellsport GmbH & Co. KG...
Need help?
Do you have a question about the blue arrow 1.0 3D and is the answer not in the manual?
Questions and answers