Advertisement
Quick Links
Printed: 14.09.2015 | Doc-Nr: PUB / 5246581 / 000 / 00
AG 125-A36
AG 150-A36
Deutsch
English
Français
Italiano
Español
Português
Nederlands
Ελληνικά
Magyar
Polski
Русский
Česky
Slovenčina
Hrvatski
Srpski
Slovenščina
Türkçe
ת י
ר ב
ע
Українська
de
en
fr
it
es
pt
nl
el
hu
pl
ru
cs
sk
hr
sr
sl
tr
he
uk
Advertisement
Related Manuals for Hilti AG 125-A36
Summary of Contents for Hilti AG 125-A36
- Page 1 AG 125-A36 AG 150-A36 Deutsch English Français Italiano Español Português Nederlands Ελληνικά Magyar Polski Русский Česky Slovenčina Hrvatski Srpski Slovenščina Türkçe ת י ר ב ע Українська Printed: 14.09.2015 | Doc-Nr: PUB / 5246581 / 000 / 00...
- Page 2 Printed: 14.09.2015 | Doc-Nr: PUB / 5246581 / 000 / 00...
- Page 3 Printed: 14.09.2015 | Doc-Nr: PUB / 5246581 / 000 / 00...
- Page 4 Printed: 14.09.2015 | Doc-Nr: PUB / 5246581 / 000 / 00...
- Page 5 Printed: 14.09.2015 | Doc-Nr: PUB / 5246581 / 000 / 00...
- Page 6 AG 125-A36 AG 150-A36 Original-Bedienungsanleitung ........
- Page 7 The type designation and serial number are printed on the type identification plate. ▶ Make a note of this data in the following table and always refer to it when making an enquiry to your Hilti representative or Hilti Service Center.
- Page 8 2 Safety 2.1 Warnings The purpose of warnings Warnings alert persons to hazards that occur when handling or using the product. Description of the key words used DANGER Draws attention to imminent danger that will lead to serious personal injury or fatality. WARNING Draws attention to a potentially dangerous situation that could lead to serious personal injury or fatality.
- Page 9 ▶ Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. ▶ Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
- Page 10 Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control. ▶ Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires.
- Page 11 ▶ The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected. ▶ The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator.
- Page 12 ▶ Dirty or dusty power tools that have been used frequently for work on conductive materials should be checked at regular intervals at a Hilti Service Center. Under unfavorable circumstances, dampness or dust adhering to the surface of the power tool, especially dust from conductive materials, may lead to damage to the power tool.
- Page 13 It is recommended that a dust removal system consisting of matched components, i.e. dust removal hood and a suitable Hilti vacuum cleaner, are used for working on mineral materials such as concrete or stone. These protect the operator and increase the life of the power tool and accessory tools used.
- Page 14 Item Equipment ACD AG-D AF-D AN-D DGCW DCD DD-M14 Clamping nut Clamping flange ‚Kwik lock‘ (optional for 3.9 Li-ion battery charge status display The charge status of the Liion battery is displayed after one of the two battery release buttons is pressed. Status Meaning 4 LEDs light.
- Page 15 Total vibration (vector sum of three directions), measured in accordance with EN 60745 Other applications, such as cutting, may produce vibration values that deviate from the given values. AG 125A36 AG 150A36 Surface grinding with the 3.2 m/s² 4.6 m/s² vibration-absorbing side handle (a h,AG Uncertainty (K)
- Page 16 5.4.2 Adjusting the guard ▶ Press the guard release button and then rotate the guard until it engages in the desired position. 5.4.3 Removing the hood 1. Press the guard release button and then rotate the guard until the triangular marks on the guard and the power tool are in alignment.
- Page 17 CAUTION Risk of breakage and irreparable damage. If the spindle lockbutton is pressed while the spindle is rotating, this may cause the accessory tool to work loose or detach from the power tool. ▶ Press the spindle lockbutton only when the spindle has stopped rotating. 2.
-
Page 18: Operation
2. Screw the accessory tool onto the drive spindle. 3. Press the spindle lockbutton and hold it in this position. 4. Use an open-end wrench to tighten the accessory tool securely and then release the spindle lockbutton. 5.7.6 Removing the accessory tool 1. - Page 19 Take your individual workplace risk assessment into account. Note To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by us for use with the product can be found at your local Hilti Center or online at: www.hilti.com...
-
Page 20: Troubleshooting
▶ Switch the power tool off im- gets very hot. mediately, remove the battery, keep it under observation, allow it to cool down and contact Hilti Service. The tool does not achieve full A battery with inadequate capacity Capacity: > 2.6 Ah power. - Page 21 Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.
- Page 22 Hilti = registered trademark of Hilti Corp., Schaan Pos. 1 | 20150617 Printed: 14.09.2015 | Doc-Nr: PUB / 5246581 / 000 / 00...
Need help?
Do you have a question about the AG 125-A36 and is the answer not in the manual?
Questions and answers