Related Manuals for Dolphin dolkpl1kb
Summary of Contents for Dolphin dolkpl1kb
- Page 1 DOLKPL1KB • DOLKPS1KB DOLKSF1KB INSTRUCTIONAL USER MANUAL VIDEO Connection Terminals Basic Wiring Example Quick Start Guide Programming Guide Specifications...
-
Page 2: Connection Terminals
Connection Terminals The DOLKPS1KB/DOLKPS1KB/DOLKSF1KB is a secure and waterproof keypad with three relay outputs. It works independently as a stand-alone keypad. WIEGAND & DATA I/O HARNESS BACK-LIT JUMPER K OR A JUMPER CONNECTION TERMINALS · 12-24V DC (Power Input Terminal) ·... - Page 3 · DU OUT (Duress Output) · When a Duress Code is entered, the DU OUT will switch to ground. Ex. It may be used to turn on a light, camera, or buzzer. It may also be used to trigger an alarm for a security system.
-
Page 4: Basic Wiring Example
Basic Wiring Example Basic wiring of a stand-alone door lock NOTE: · Connect 1N4004 as close as possible to the lock parallel with the lock power terminals to absorb the back EMF and prevent keypad damage. The 1N4004 is not required for AC power. ·... - Page 5 Quick Start Guide As the DOLKPS1KB/DOLKPS1KB/DOLKSF1KB is powered, it will begin its booting process and beep for 1 minute. When the DOLKPS1KB is finished: Enter Programming Mode and Add Users NOTE: Default Master Code 0000 Master Code (4-8 digits) Master Code (4-8 digits) User Number User Access Code...
- Page 6 THE JUMPER FOR BACKLIT OPTIONS Located on the upper-left corner; the two options are for full lights or auto lights. 1. Full backlit – The keypad constantly illuminates. 2. Auto backlit – The keypad only illuminates during use. DIRECT ACCESS PROGRAMMING WITH CODE: 8080 If you have forgotten the master code there is still a way to enter programming mode.
-
Page 7: Programming Chart
Programming Chart Feature Code Entry Comments Begin Master Code Set System into Program- Programming ming Mode. The default Mode (Solid Master Code is 0000. Yellow) Note: All of the following commands must be keyed while in Programming Mode. Return to normal Programming operation. -
Page 8: Sound Settings
Delete Visitor 40 Visitor number # Delete the visitor’s code. Code (1-50) Clear all Visitor 40 0999 # Clear all Access Codes. Codes Lock Settings Set door unlock 5 Output number Set the amount of sec- timer onds the device will grant (1, 2 or 3) access before locking Seconds #... -
Page 9: Specifications
Auto/Manual Code Entry Settings Auto Code 7 01 # The # key after entering Entry Mode an access code will NOT be required. Important Note: For this feature to work, ALL codes must be the same number of digits as the master code. - Page 10 Egress Button: Programmable for Instant, Delay with Warning and/or Alarm Momentary or Holding Contact for the Exit Delay Input Sensing Terminals: a) Door position, b) Egress, c) O/P 1 inhibit Output Control Terminals: Transistor Open Collector 24VDC/100mA sink Max for the following outputs a) Duress, b) Alarm, c) Key Active, d) Output 3 (Door Bell version only), e) Inter-lock...
- Page 11 TRANSMITTER SOLUTIONS WARRANTY The warranty period of this product is 12 months from the purchasing date. During this period, if the product does not operate correctly due to a defective component, the product will be repaired or replaced at the sole discretion of Transmitter Solutions. This warranty does not extend to the product’s casing, which can be damaged by conditions outside of the control of Transmitter Solutions.
- Page 12 7380 S. Eastern Ave, Suite 124-320 • Las Vegas, NV 89123 (866) 975-0101 • (866) 975-0404 fax www.transmittersolutions.com...
Need help?
Do you have a question about the dolkpl1kb and is the answer not in the manual?
Questions and answers