OVERVIEW OF COMPONENTS ..........................11 New Elegance MINI Control 1GR ..................................11 New Elegance MINI Pulser 2GR ..................................12 New Elegance MINI Control 1GR with grinder .............................13 New Elegance Control 2GR ....................................14 New Elegance Control 2GR with grinder ................................15 New Elegance Control 3GR ....................................16 DIMENSION SKETCH ..............................17...
Page 3
CONTENTS New Elegance PROGRAMMING ................................25 Electronic control panel .......................................25 Button functions ........................................25 Machines with display ......................................25 Machines without display .....................................25 Additional button functions ....................................25 Additional functions accessible from the display ............................26 User functions ........................................26 Counters ..........................................26 Accessing the counters ......................................27 Litre counter ...........................................27...
Page 4
Mini Control 2Gr (220-240V, 1N~ 50-60 Hz 3350W) ..........................42 Mini Control 1Gr with Grinder (220-240V, 1N~ 50-60 Hz 3125W) ...................... 43 New Elegance 2Gr Display Control (220-240V, 1N~ 50-60 Hz 3200W) ....................44 New Elegance 2Gr Control (220-240V, 1N~ 50-60 Hz 3200W) ......................45 New Elegance 2Gr Pulser (220-240V, 1N~ 50-60 Hz) ..........................
SYMBOL DESCRIPTION New Elegance Hazard intensity levels There are three different levels of hazard intensity, identified by signal words DANGER, WARNING and IMPORTANT. The level of hazard is determined by the following definitions. Observe the statements to ensure safety, performance, prevent injury and machine damage.
GENERAL New Elegance Introduction Thank you for choosing the New Elegance espresso machine. We hope you enjoy it ! Read the user manual before using the machine. Keep this manual close to hand for future This manual contains important instructions on reference.
GENERAL New Elegance Do not remove or disable any of the mechanical, units of the same model. Do not place other electrical or thermal protection mechanisms. heavier packages on top of the box. In case of emergency, (e.g. the machine catches fire...
TECHNICAL SPECIFICATIONS New Elegance New Elegance 1GR New Elegance 1GR SPECIFICATIONS MINI Control MINI Pulser MINI with grinder EAED-C32B-12AB Machine model, Standard 220-240V 1N~ 50-60 Hz 2770W EAED-C32B-22AB Machine model, Take Away 220-240V 1N~ 50-60 Hz 2770W Steam wand 1 unit...
TECHNICAL SPECIFICATIONS New Elegance New Elegance Control 2GR New Elegance 2GR New Elegance 2GR SPECIFICATIONS SPECIFICATIONS Control with Control with MINI Control Mini Pulser Pulser Control Control grinder grinder EBED-C32B-12AB EBFE-D13B-12AB EBEE-D32B-12AB Steam wand 1 units Machine model, Standard 220-240V 1N~...
TECHNICAL SPECIFICATIONS New Elegance New Elegance Display Control New Elegance Display Control SPECIFICATIONS 3-4GR EBEE-D41B-12AB Machine model, Standard 220-240V 1N~ 50-60 Hz 3200W EBEE-D41B-22AB Machine model, Take Away 220-240V 1N~ 50-60 Hz 3200W Steam wand 2 units Hot water outlet...
OVERVIEW OF COMPONENTS New Elegance Front View New Elegance MINI Control 1GR Drink but- Hot water Steam tap tons Brewing group Hot water outlet Steam wand Porta-filter Heater element lamp Boiler pressure gauge Boiler pressure gauge...
OVERVIEW OF COMPONENTS New Elegance Front View New Elegance MINI Pulser 2GR Switch of right brewer Switch of right brewer Steam tap Hot water tap water outlet Boiler pressure gauge Brewing group Porta-filter Steam wand Heater element lamp...
OVERVIEW OF COMPONENTS New Elegance Front View New Elegance MINI Control 1GR with grinder Grinder Drink but- Hot water Steam tap tons Brewing group Hot water ON/OFF outlet switch Steam wand Porta-filter Boiler pressure gauge...
OVERVIEW OF COMPONENTS New Elegance Front View New Elegance Control 2GR Drink buttons Drink buttons for left brewer for right brewer Hot water Hot water Switch of left Steam tap brewer Switch of right Steam tap brewer Boiler pressure gauge...
OVERVIEW OF COMPONENTS New Elegance Front View New Elegance Control 2GR with grinder ON/OFF Grinder switch Boiler pres- Drink but- Hot water Steam tap sure gauge tons Brewing group Hot water Steam wand outlet Porta-filter Power switch...
OVERVIEW OF COMPONENTS New Elegance Front view of the machine New Elegance Control 3GR Drink buttons Steam tap Boiler pressure gauge ON/OFF switch Steam tap Hot water tap Power switch Hot water outlet Heater element lamp Steam wand Porta-filter Brewing...
DIMENSION SKETCH New Elegance New Elegance MINI 1GR Model Mini control 1GR 510 mm 500 mm 600 mm 74 mm Mini pulser 1GR 510 mm 500 mm 600 mm 74 mm New Elegance MINI 2GR Model Mini control 2GR 510 mm...
DIMENSION SKETCH New Elegance New Elegance MINI 1GR with grinder Model Mini control 1GR with grinder 690 mm 500 mm 600 mm 74 mm Mini pulser 1GR with grinder 690 mm 500 mm 600 mm 74 mm New Elegance Control 2GR...
DIMENSION SKETCH New Elegance New Elegance 2GR with grinder Model Pulser 2Gr with grinder 670 mm 710 mm 600 mm 124 mm Control 2Gr with grinder 670 mm 710 mm 600 mm 124 mm Display control 2Gr with grinder 670 mm...
TRANSPORT New Elegance Packaging The machine is shipped in a unique carton box which uses expanded polystyrene paddings. The machine box is provided with conventional symbols that can be perfectly visible during the handling and storage tasks. The machine box must stay in a vertical position during the transport. Do not tip or try to place the box tilted sideways in any way.
INSTALLATION AND START UP New Elegance Electrical connection The coffee machine should only be connected to the power supply by qualified personnel. The following safety instructions should be followed at all times: Check that the electrical specifications on the ratings plate match the specifications of the power supply at the point of installation.
INSTALLATION AND START UP New Elegance Water connection Connecting the machine to the domestic water supply must be performed by a qualified person. Purge at least 20 liters of water from the domestic water supply before connecting the machine to it to flush out any debris that may be in the plumbing sytem that would otherwise accumulate inside the boilers.
Remove the shower and gasket. Remove and discard the old gasket. straight-blade screwdriver to release Insert the new gasket (chamfer and the shower by prying down with EXPOBAR logo facing up) into the medium force. shower. > 65 Remove the filter basket(A), then Preheat the gasket to soften the rubber.
CLEANING AND CARE New Elegance Insert the preheated gasket and Rotate the porta-filter into its Remove the porta-filter. The new gasket shower into the head group using locked position using medium and shower will remain inside the head the porta-filter. Use both hands.
PROGRAMMING New Elegance Electronic control panel Button functions The electronic keypad controls the following functions: Volume control of four different espresso drinks per brewing group. Time-controlled hot water dispensing. (if available) Automatic filling and level control of the boiler. Automatic switch off of the heating element if not enough water.
PROGRAMMING New Elegance Additional functions accessible from the display CREM XXX ºC hh:mm Programmable public- Current time EXPOBAR SELECT Boiler temperature Machines equipped with a display include the following additional functions: Automatic daily on/off timer (stand-by). Clock settings (current time and date).
PROGRAMMING New Elegance Accessing the counters With the machine switched ON, hold down the Continuous Dispensing button Dose programming Select 30 s for over 8 seconds (until the "Dose programming" menu is displayed, see Fig. 02 fig. 02). Set clock Hold down the Continuous Dispensing button until the "Set clock"...
PROGRAMMING New Elegance Service: service alert This counter displays the number of coffees/infusions (individual servings) dispensed by Service the machine (see fig. 06). NNNN How to access it: Press the Continuous Dispensing button when the litre Fig. 06 counter is displayed.
SERVICE PROGRAMMING New Elegance Reset parameters to factory default To reset the control panel settings to the factory default: Data reset Switch off the machine at the power switch. completed Press and hold down the '1 Short Espresso' , 2 Short Espressos Fig.
SERVICE PROGRAMMING New Elegance Name 1: Programming the publicity display (upper line) The display comprises two rows of 16 characters. The publicity messages displayed on Name 1 these two lines can be edited in this menu (see fig. 13) and the next one.
SERVICE PROGRAMMING New Elegance Dose programming This menu is used to enable/disable coffee-dose programming (see fig. 16). Dose programming When disabled, users are not able to modify the doses (as described in the user Enabled/Disabled manual). This mode is intended to prevent users setting inappropriate doses.
SERVICE PROGRAMMING New Elegance Electronic steam wand If the machine has an electronic steam wand (no manual steam tap), this menu is used Steam tap Gr. to select (via the Continuous Dispensing button) which button panel will control the wand.
SERVICE PROGRAMMING New Elegance Grinding alert This setting is used to enable/disable the coffee-dispensing monitor (see fig. 22). This Grinding alert analyses dispensing speed and, depending on this value, indicates if the coffee is too Enabled/Disabled finely or too coarsely ground. If the dispensing speed is between the pre-established values, the "OK"...
SERVICE PROGRAMMING New Elegance Maintenance cycles This menu sets the number of coffees dispensed per maintenance cycle (before Maintenance cycles replacing shower plates, gaskets, etc.). When the dispensing counter reaches the N000 number set (see fig. 26), the "Service" message will be displayed.
New Elegance Digital thermostat functions In multi-boiler models, each dispensing group has an independent digital boiler-temperature adjustment system. The following multi-boiler New Elegance models are available: 2 dispensing groups and 3 boilers. 3 dispensing groups and 4 boilers. Temperature is controlled by a digital thermostat to ensure optimal temperature stability at each group spout.
MULTI-BOILER PROGRAMMING New Elegance Setting group temperature To adjust the group temperature maintained by the thermostat, follow the instructions below with the machine turned on and the thermostat connected: Briefly press the button. The thermostat will display the "PrG" message Fig.
MESSAGES AND ALARMS New Elegance Alarm Fault in volumetric counter N / Flow fault detected in counter N Counter Vol. Gr. N Time-out alarm Check that the machine is receiving water. Boiler filling Sensor fault Temperature gauge fault Service the machine.
TROUBLESHOOTING New Elegance The following checks can be carried out by users once the machine has been turned off and disconnected from the power supply. For all other non-specified machine faults, disconnect the machine from the power supply and immediately contact authorised and qualified service personnel.
ELECTRICAL COMPONENTS New Elegance New Elegance Mini 2Gr View Part No. Description C60100310 Switchboard 1D5 New Elegance 220V Probe C60100410 Control Board 3D5 Xlc C60800100 Static Relay C60900035 Switch Red Components common to all models View Part No. Description C60800103...
EXPLODED VIEWS New Elegance Housing - MINI 1Gr with Grinder Drawing...
Page 52
Lower Box Mini 13109100BH Nw Eleg. Left Side Panel Black H/G 13109000BH New Eleg. Right Side Panel Black H/G 13110200 Central Bodywork Mini Inox New Elegance 13020041 Cup Tray Mini Elegance W/Grinder 13100000 Right Trim Inox New Elegance 13110010 Top Fr Panel Minicon-Puls 1Gr W/G N.Ele 17000100 Group Cover Support G-10/ N.
EXPLODED VIEWS New Elegance Housing - MINI 1 & 2 Gr Drawing...
Page 54
Lower Box Mini 13109100B Nw Eleg. Left Side Panel Black 13109100B Nw Eleg. Left Side Panel Black 13110200 Central Bodywork Mini Inox New Elegance 13020041 Cup Tray Mini Elegance W/Grinder 13100000 Right Trim Inox New Elegance 13110000 Top Front Panel Minicon-Puls 1Gr New Ele...
EXPLODED VIEWS New Elegance Housing - 2GR with Grinder Drawing...
Page 56
Lower Box 2-3-4Gr 20000012 Base Chassis 2Gr H/Gr (High Group) 20000010 Base Chassis 2Gr Elegance (Standard) 13100100 Left Trim Inox New Elegance 13109100BH Nw Eleg. Left Side Panel Black H/G 11100045 Cup Tray Eleg 2Gr Grinder Ec 13120200 Central Bodywork 2Gr N. Elegance 13109000BH New Eleg.
EXPLODED VIEWS New Elegance Housing - 2GR Drawing...
Page 58
Central Bodywork 2Gr N. Elegance 13120110 Top Front Panel Control 2Gr+Tap N. Eleg 13120010 Top Front Panel Control 2Gr+Tap N. Eleg 13120020 Top Front Panel Display 2Gr New Elegance 20000110 Frontal 2Gr Inter/Elegance 11000110 Frontal 2Gr Ec/Monroc 19000110 Frontal 2 Gr Mega-Markus...
EXPLODED VIEWS New Elegance Housing - 3GR Drawing...
Page 60
Nw Eleg. Left Side Panel Black 13010040 Cup Tray 3Gr Elegance 13010043 Cup Tray 3 Gr Elegance (Bou) 13130200 Central Bodywork 3Gr Inox New Elegance 13109000B Nw Eleg. Right Side Panel Black 13100000 Right Trim Inox New Elegance 13130100 Top Front Panel Cont Display.3Gr New Ele 13130000 Top Front Panel Cont.3Gr New Elegance...
EXPLODED VIEWS New Elegance Water System - MINI 1Gr Pulser & Control, Standard & Take Away Drawing 1Gr. MINI Control - Standard and TA (For use with (For use with Control models.) Pulser models.)
Page 62
EXPLODED VIEWS New Elegance Water System - MINI 1Gr Pulser & Control, Standard & Take Away Spare parts list POS. Part No. Description C15000370 Tap Steam Eleg./Mega Comp 4H Bf C60000062 D-40 One Reading Manometer Orman C35040117 4Ltrs Grinder's Steam Pipe...
EXPLODED VIEWS New Elegance Water System - MINI 2Gr Pulser & Control, Standard & Take Away Drawing...
Page 64
Pipe Group Left Return Mini C35110002 Pipe Group Right Inlet C35110003 Pipe Group Left Inlet CESC00100 Magnets Set -------- Boiler Assembly New Elegance Mini C35040106 Pipe Pressure Sensor Mini C60000008 Pressostat Piris Ce C35040118 Pipe Water Filling Mini C35040105 Pipe Group Right Return Mini...
EXPLODED VIEWS New Elegance Water System - MINI 2 Gr Pulser & Control, Standard & Take Away Drawing...
Page 66
EXPLODED VIEWS New Elegance Water system - 2 GR MINI Pulser & Control, Standard & Take Away Spare parts list POS. Part No. Description C15000370 Tap Steam Eleg./Mega Comp 4H Bf C60000062 D-40 One Reading Manometer Orman C35040117 4Ltrs Grinder's Steam Pipe...
EXPLODED VIEWS New Elegance Water system - 2Gr Pulser & Control, Standard & Take Away Drawing (For use with Std. models.) (For use with Take Away models.)
Page 68
EXPLODED VIEWS New Elegance Water system - 2Gr Pulser & Control, Standard & Take Away Spare parts list POS. Part No. Description C35900020 30Cm Hose C15000370 Tap Steam Eleg./Mega Comp 4H Bf C35040117 4Ltrs Grinder's Steam Pipe C60000065 1 Gauge Reading D-60...
EXPLODED VIEWS New Elegance Water system - 2Gr Display, Standard & Take Away Drawing (For use with Std. models.) ESC00060 (For use with Take Away models.)
Page 70
EXPLODED VIEWS New Elegance Water system - 2Gr Display, Standard & Take Away Spare parts list POS. Part No. Description C35900020 30Cm Hose -------- Steam tap C35110113 Pipe Steam Tap C35110465 Pipe Water Filling 2Gr Mc -------- Water throws + E.V. 2-way 1 / 4G...
EXPLODED VIEWS New Elegance Water system - 2Gr Pulser & Control, Standard models with Manual Tap Drawing 05 06 07 15 16 (For use with Control models.) (For use with Pulser models.) 2Gr Conrol Std. with Manual Tap 2Gr Pulser Std. with Manual Tap 2Gr Conrol Std.
Page 72
EXPLODED VIEWS New Elegance Water system - 2Gr Pulser & Control, Standard models with Manual Tap Spare parts list POS. Part No. Description C35900020 30Cm Hose C15000370 Tap Steam Eleg./Mega Comp 4H Bf C35040117 4Ltrs Grinder's Steam Pipe C60000065 1 Gauge Reading D-60...
EXPLODED VIEWS New Elegance Water system - 2Gr, 3 boilers Drawing 05 06...
Page 74
EXPLODED VIEWS New Elegance Water system - 2Gr, 3 boilers Spare parts list POS. Part No. Description C15000370 Tap Steam Eleg./Mega ComP 4H BF -------- Water throws + E.V. 2-way 1/4G C60000062 D-40 One Reading Manometer Orman C35040117 4Ltrs Grinder's Steam Pipe...
EXPLODED VIEWS New Elegance New Elegance: Rotary pumps Drawing...
Page 80
O-Ring 8 X 1.9 C65000010 Retention Valve C60000030 Pump (Crem Special Treatment) C60000031 Piston Bypass Pump (Tec) C60000033 Pump Rotary Compact CESCMPS00 Motor&Pump Ass Std CESCMPE00 MOTOR&PUMP ASS ECO Note: Part No. C30400055 and CESCMPE00 apply to the New Elegance Mini models.
Page 82
EXPLODED VIEWS New Elegance Group head Spare parts list POS. Part No. Description C30200035 Long Plug 1/2 Group C50010040 21.7*25.7*2 G/C-G Teflon Gasket C70000009 Group Teflon Injector Rev3 C30200061 Group Teflon Injector Rev3 C30200026 Tefl Water Reduc. Holder 4X6x65 C25091250...
EXPLODED VIEWS New Elegance Portafilters Drawing 02 03...
Page 84
EXPLODED VIEWS New Elegance Portafilters Spare parts list POS. Part No. Description C75000059 1 Cup Filter 6 Gr C75000037 1 Cup Filter 6,5 Gr C75000031 1 Cup Filter (7Gr) C75000050 Spout 1Cup C75000041 2 Cup Filter (14Gr) C75000060 Spout 2Cups...
EXPLODED VIEWS New Elegance New Elegance Mini 1Gr : water supply and drainage set Drawing Spare parts list POS. Part No. Description C30000510 Conical Adaptor 1/4*1/4 Electron C60000100 1/4 X 1/4 Electrovalve Parker 220V C60000103 1/4 X 1/4 Electrovalve Parker 120V C50010020 13.2*18.2*2.5 1/4 Teflon Gasket...
Page 86
EXPLODED VIEWS New Elegance New Elegance Mini 2Gr : water supply and drainage set Drawing Spare parts list POS. Part No. Description C60000100 1/4 X 1/4 Electrovalve Parker 220V C60000103 1/4 X 1/4 Electrovalve Parker 120V C30100010 Hexagonal Nut 1/4 Pressostat...
EXPLODED VIEWS New Elegance New Elegance 2Gr: water supply and drainage set Drawing...
Page 88
EXPLODED VIEWS New Elegance New Elegance 2Gr: water supply and drainage set Spare parts list POS. Part No. Description C60000105 50/60Hz 220V Solenoid Electrovalve C50000105 Large Autofill Solenoid Gasket C50000110 Small Autofill Solenoid Gasket C30000215 Conical Bend Adaptor 1/4 X 1/4...
EXPLODED VIEWS New Elegance Steam tap Drawing 05 06 07...
Page 92
EXPLODED VIEWS New Elegance Steam tap Spare parts list POS. Part No. Description C30370070 Tap Body C30370060 Close Nut C30370050 Closing Shaft M-6 C30370040 Shaft Spring C30370065 Push Cap C30370020 Shaft Ring C30370030 Gasket C30370010 Tap Fitting C30370140 Tap Fixing Nut...
EXPLODED VIEWS New Elegance Hot water taps Drawing 01 02 05 06 07...
Page 94
EXPLODED VIEWS New Elegance Hot water taps Spare parts list POS. Part No. Description C30370070 Tap Body C30370060 Close Nut C30370050 Closing Shaft M-6 C30370040 Shaft Spring C30370065 Push Cap C30370020 Shaft Ring C30370030 Gasket C30370010 Tap Fitting C30370140 Tap Fixing Nut...
SERVICE INTERVALS New Elegance New Elegance Mini Control 1Gr & 2Gr Months (Cycles) Main components Part No. 6 (12500) 12 (25000) 18 (37500) 24 (50000) Boiler Non suction valve Replace Replace C65000200 Replace 1/4 X 1/4 Electrovalve Parker 220V C60000100...
For the warranty to be valid, the conditions for maintenance must have been followed in accordance with our instructions, proper care must have been taken and any claim against the warranty must be sent without delay. The equipment in question may not be used while awaiting service if there is any risk that the damage or defect would worsen.
Need help?
Do you have a question about the NEW ELEGANCE and is the answer not in the manual?
Questions and answers