Table of Contents
Advertisement
Setup menus
<TIME CODE>
(continued)
No./Item
1
For setting how the user's bit of the time code
508*
generated by the TCG is to be used.
0000
000:
BINARY GP
NOT SPECIFIED (no character set specified)
0001
001:
ISO
CHARACTER
complying with ISO646, ISO2022 standards)
0002
010:
0003
011:
0004
100:
0005
101:
0006
110:
0007
111:
509
For selecting whether to exercise phase
correction control over the LTC which is
PHASE CORR
generated by the TCG.
0000
OFF:
Phase correction control is not exercised.
0001
ON:
Phase correction control is exercised.
1
For selecting whether to set the CF flag of the
510*
TCG to ON or OFF.
0000
OFF:
TCG CF FLAG
0001
ON:
2
For selecting the drop frame or non-drop
511*
frame mode for CTL and TCG.
0000
DF:
DF MODE
0001
NDF:
<Note>
This DF mode setting takes effect only when LOCAL is
selected or when "ENA" has been selected as the setup
menu item No.001 (LOCAL ENA) setting.
1
For switching the phase of the time code,
512*
which is output from the TIME CODE OUT
connector, in response to the external LTC
TC OUT REF
input when a setting other than "INT" has
been selected for setup menu item No.507 (TC
SOURCE). (In EE mode only)
0000
V OUT:
0001
TC IN:
SBC (sub code data) area:
This is an area on the helical track, and it is separate from the video
and audio data area. The time codes, recording dates and times
and other tape control information complying with SMPTE/EBU
standards are stored here. As with the conventional LTC (linear time
code), the time code can be read even during rewinding or fast
forwarding. It can also be read out when the tape has stopped.
VAUX (video auxiliary data) area:
This area is to be found in the video data area on the helical track.
The additional information relating to the video data is stored here.
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode
has been selected as the system menu item No.25 (SYSTEM FREQ)
setting.
*2: This item is not displayed when the 23/24 Hz, 25 Hz (HD or SD) or 50 Hz
mode has been selected as the system menu item No.25 (SYSTEM
FREQ) setting.
92
Description of setting
(8-bit
character
UNASSIGNED 1 (undefined)
UNASSIGNED 2 (undefined)
UNASSIGNED 3 (undefined)
PAGE/LINE
UNASSIGNED 4 (undefined)
UNASSIGNED 5 (undefined)
The CF flag is set to OFF.
The CF flag is set to ON.
The
drop
frame
mode
selected.
The non-drop frame mode is
.
selected
The phase is aligned with the
output image.
The phase is aligned with the
external time code input.
No./Item
513
For selecting how to output the VITC which is
superimposed on the output video signal.
VITC OUT
0000
In the playback mode, the time code recorded
in the SBC area is output.
set
0001
In the playback mode, the time code recorded
in the VAUX area is output.
<Note>
The VITC information detected by the HD serial input is
automatically recorded in the VAUX area when the video
signals are recorded
514
For selecting whether to superimpose the
VITC information on the HD serial output.
HD
EMBD
0000
VITC
The VITC information is not superimposed.
0001
The VITC information is superimposed.
515
For selecting whether to superimpose the
LTC information on the HD serial output.
HD EMBD LTC
0000
The LTC information is not superimposed.
0001
The LTC information ist superimposed.
1
For selecting the processing to align the
516*
phase of the time code which is output from
the TIME CODE OUT connector.
TC OUT ADV
is
Normally, the time code which is output from the
TIME CODE OUT connector is aligned with the
output video and audio. If so required by the
connection with an external component or for
some other reason, this item makes it possible to
set the mode for aligning the phase with the
input.
0000
The phase alignment processing is not
conducted. The time code which is output
from the TIME CODE OUT connector is
aligned with the output video and audio.
0001
During playback when an editing mode has
been selected and during editing, the time
code which is output from the TIME CODE
OUT connector is aligned with the input video
and audio. In all other modes, it is aligned with
the output video and audio.
1
For selecting whether to latch the TCG
517*
display and LTC output during INPUT CHECK.
0000
TCG OUT
The INPUT CHECK mode is established only
while the INPUT CHECK key is held down.
0001
When the INPUT CHECK key is pressed, the
INPUT CHECK mode is established; even
when it is released, the mode remains
unchanged. The selection is released when
the video output is set to a mode other than the
EE mode.
The underlining (__) denotes the factory setting mode.
Description of setting
SBC:
VAUX:
.
OFF:
ON:
OFF:
ON:
OFF:
EDIT:
MOMENT:
LATCH:
Advertisement
Table of Contents
