Panasonic HD1700pe Operating Instructions Manual page 85

Setup menus
<OPERATION>
(continued)
No./Item
112 For selecting what playback images are to be
output in the STANDBY OFF mode and EJECT
FRZ MODE mode.
SEL 0000 DIS:
The video output is muted.
0001 STB OFF:
Only when the STANDBY OFF mode is
established is the image which was being
played back at that moment frozen and output.
0002 SOF&EJ:
When either the STANDBY OFF mode or the
EJECT mode is established, the image which
was being played back at that moment is
frozen and output.
<Notes>
• The status when the picture is frozen is determined
by the setup menu item No.604 (FREEZE SEL)
setting.
• In the EJECT mode, the frozen picture is output only
when 1 (BLACK) or 2 (GRAY) has been selected as
the setup menu item No.106 (EJECT EE SEL)
setting.
• The picture freeze is forcibly released if a change has
occurred in the output format of the HD serial output
signals when operation has transferred to the EJECT
mode.
Description of MEMORY STOP function
0 point
REW
3
button
FF
4
button
! If the FF button is pressed, the normal FF operation is performed
since there is no 0 point in the direction of this operation.
@ If the REW button is pressed, the PREROLL lamp lights (as does
the SHTL lamp), the VTR prerolls the tape, and it automatically
stops when the counter value is at the 0 position.
# If the REW button is pressed, the normal REW operation is
performed since there is no 0 point in the direction of this
operation.
$ If the FF button is pressed, the PREROLL lamp lights (as does
the SHTL lamp), the VTR prerolls the tape, and it automatically
stops when the counter value is at the 0 position.
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or
SD) mode has been selected as the system menu item No.25
(SYSTEM FREQ) setting.
The underlining (__) denotes the factory setting mode.
Description of setting
The MEMORY STOP function does
not work if this margin is less than
d2 frames.
FF
1
button
REW
2
button
No./Item
1 For selecting whether to allow or inhibit recording
113*
on the cassette tape.
0000 OFF:
REC INH
Recording on the cassette tape is enabled when the
cassette's accidental erasure prevention mechanism
has been set to the recording enable position.
0001 ALL:
All recording on the cassette tape is inhibited.
0002 PRE:
Overwriting is inhibited during normal recording.
This is the setting to activate the accidental erasure
prevention function. While CTL is detected, the
recording is inhibited, and when CTL cannot be
detected, it is executed.
0003 NORM:
Normal recording is inhibited.
Use this setting when it is preferable to avoid
using normal recording in all applications
except for editing.
0004 V/CTL:
The recording of the video and CTL signals is
inhibited.
Use this setting when it is preferable to avoid editing
in all applications except for audio editing.
<Note>
When the PRE, NORM or V/CTL setting has been
selected, the REC INHIBIT lamp blinks (on for approx.
0.5 sec. and then off for approx. 0.5 sec.).
114 For selecting whether the REC INHIBIT lamp is to
blink or light when the cassette tape has been set
REC INH to the accidental erasure protection mode.
LAMP 0000 LIGHT:
0001 FLASH:
<Note>
If 1 (ALL) has been selected as the setup menu item
No.113 (REC INH) setting, the REC INHIBIT lamp will
be lighted at all times regardless of the REC INH LAMP
setting.
1 For selecting whether to enable or disable the
115*
operation of the EJECT button on the VTR's
front panel.
EJECT SW
0000 REC:
INH
0001 OFF:
Accidental erasure protection function
This function is used to prevent parts already recorded on a tape from being
recorded over. Accidental erasure of pre-recorded tapes is prevented by
positioning the CTL signal rec/play heads as shown in the figure below so that
whether a recording has been made can be determined by the presence or
absence of the CTL signal. When the REC/PLAY button is pressed with a pre-
recorded tape, the tape runs but the REC button lamp blinks, the beeping
alarm is sounded, and no signals are recorded.
PRE CTL
head
Rough sketch showing CTL head positions
Description of setting
The lamp lights.
The lamp blinks.
Operation is disabled while the
VTR is in the recording mode.
Operation is enabled in all
modes.
A/C heads
(rec/play heads)
85