Table of Contents
Advertisement
Setup menus
<OPERATION>
(continued)
No./Item
116
For selecting whether the EJECT lamp is to remain
lighted or go off after the cassette tape has been
EJECT LAMP
ejected.
0000 MODE1:
The EJECT lamp remains lighted.
0001 MODE2:
The EJECT lamp goes off.
1
For selecting whether to allow or inhibit
118*
recording on a tape which has been written
by a format other than DVCPRO HD-LP.
SP MODE
0000
OFF:
INH
Recording on the cassette tape is allowed.
0001
ON:
Recording on the cassette tape is inhibited.
<Notes>
• When 0 (OFF) has been selected, whether recording
on the cassette tape is allowed or inhibited is
determined by the setup menu item No.113 (REC
INH) setting.
• The recording format is determined by the setup
menu item No.020 (SYS FORMAT) setting.
131
For selecting what cue point operation is to
be performed when the multi cue function has
PAGE MODE
been set to ON.
0000
MANU:
Operation is confined within the selected page,
and 6 cue points can be registered.
0001
AUTO:
When the page whose cue points are being
registered
automatically transferred to the next page, and
registration is continued. A total of 60 cue
points on up to 10 pages can be registered.
132
For
selecting
registration operation if all the cue points
ROTA MODE
have already been registered when the multi
cue function has been set to ON.
0000
OFF:
No further cue points are registered.
0001
ON:
The registration operation is continued. If "MANU"
has been selected as the setup menu item No.131
(PAGE MODE) setting, the next cue point is
registered at CUE¢1 on the page concerned; if
"AUTO" has been selected, it is registered at CUE01.
133
For setting the volume of the sound heard
when the keys are touched.
KEY BEEP
0000
OFF
0001
LOW
0002
HIGH
134
For setting the volume of the alarm tone.
0000
OFF
ALARM BEEP
0001
LOW
0002
HIGH
<Note>
If the fan motor has shut down, the alarm tone is sounded
at the HIGH volume level regardless of this setting.
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or
SD) mode has been selected as the system menu item No.25
(SYSTEM FREQ) setting.
The underlining (__) denotes the factory setting mode.
86
Description of setting
becomes
full,
operation
whether
to
perform
No./Item
1
For selecting the output signals.
140*
0000
<In the STOP mode>:
OUTPUT
The input signals selected by setup menu items
No.600 (VIDEO IN SEL) and No.713 (CH1 IN SEL)
to No.724 (D IN SEL 78) are output.
<During recording or editing>:
The input signals selected by setup menu items
No.600 (VIDEO IN SEL) and No.713 (CH1 IN SEL)
to No.724 (D IN SEL 78) are output:
0001
<In the STOP mode>
The signals played back from the tape are output.
<During recording or editing>:
The simultaneous playback signals are output.
<Note>
In order to select the output signals during recording or
editing, set setup menu item No.302 (CONFI EDIT).
1
For setting what is to be controlled by the
141*
audio volume controls on the front panel.
0000
VOLUME
The controls function as REC volume controls.
0001
The controls function as PB volume controls.
0002
Normally, the controls function as PB volume
controls.
EE/INPUT CHECK status, they automatically
function as REC volume controls.
is
1
For selecting the conditions under which the
142*
AUDIO UNITY lamp on the front panel is to light.
0000
AUDIO UNITY
The lamp lights when all the audio input levels
are set to the UNITY level.
the
0001
The lamp lights when all the audio output
levels are set to the UNITY level.
0002 IN/OUT:
The lamp lights when all the audio input and
output levels are set to the UNITY level.
143
For setting whether the lighting of the tape
mechanism is to be set to ON or remain OFF.
CASSTT
0000
LIGHT
The mechanism does not light even when a
cassette is inserted.
0001
The mechanism lights when a cassette is inserted.
144
For switching the preset registration method
for the time code.
TC INPUT
0000 NORMAL:
The time code is input starting with the left-
most digit.
0001
The time code is input from the high-order digit
but is displayed from the right-most digit.
145
For selecting whether the LCD monitor display on
the front panel is to be turned on or off.
FRONT LCD
0000
The display is turned off.
0001
The display is turned on or off in synchronization
with the screen saver operation for the time code
display area.
Description of setting
EE:
TAPE:
REC:
PB:
AUTO:
However, during recording or in the
IN:
OUT:
OFF:
ON:
REV:
OFF:
ON:
Advertisement
Table of Contents
