Table of Contents
Advertisement
System menus
No./Item
18
For adjusting the SCH phase.
When the
SHIFT
DW
SCH (SD)*
the submenu screen; press the
return the display from the submenu screen.
Submenu screen
00
For adjusting the SCH phase in 90o o steps
(The SC phase changes, and the H phase remains
COARSE
unchanged.)
0000:
0001:
0002:
180
0003:
270
01
For adjusting the SCH phase over a total variable
range of more than d45o o .
FINE
j: To advance the phase. i: To delay the phase.
(The SC phase changes, and the H phase remains
unchanged.)
0000
j32
:
0032
:
0064
20
For adjusting the audio output phase in relation to
the video output phase in 20.8¨s steps.
AV PHASE
j: The audio output phase is advanced in relation to
the video output phase.
i: The audio output phase is delayed in relation to
the video output phase.
0000
j100
:
0100
:
0200
100
25
For selecting the system frequency.
0: The 59.94 Hz or 60 Hz system frequency is selected.
SYSTEM
1: The 50 Hz system frequency is selected.
FREQ*
2: The 23.98 Hz or 24 Hz system frequency is selected.
3: The 25 Hz system frequency is selected.
However, with SD SDI and video output signals, there
is a delay of approximately one field compared with
the HD SDI output.
4: The 25 Hz system frequency is selected.
However, HD SDI output is muted.
0003
59/60
0001*
50*
0002
23/24
0003
25 (HD)
0004
25 (SD)
59/60 Hz mode:
50 Hz mode:
23/24 Hz mode:
25 Hz (HD) mode: Status in which "3" (25 (HD)) has been
25 Hz (SD) mode: Status in which "4" (25(SD)) has been
<Notes>
• This setting remains unchanged even when the
factory setting operation is performed.
• For the steps to take to switch the system
frequency, refer to page 105.
80
Description of setting
button is pressed, the display transfers to
button again to
SHIFT
0
90
:
0
:
32
:
0
:
* The asterisk denotes the
factory
setting
for
HD1700E
Status in which "0" (59/60) has been
selected
Status in which "1" (50) has been
selected
Status in which "2" (23/24) has been
selected
selected
selected
No./Item
30
For selecting whether to set or release the
system file lock mode.
MENU LOCK
0000
0001
<Note>
Even when "ON" is selected, the data will be overwritten
when the system file has been set to LOAD from the IC
card.
*System switching
• Some of the system menu and setup menu items each have
different settings for different operation modes (59/60 Hz, 50
Hz, 23/24 Hz and 25 Hz (HD or SD)). These settings are
saved separately.
(This concerns those items whose settings were described
for each operation mode on the system menu and setup
menu tables.)
• For further details, refer to "How to switch the system
frequency" on page 105.
• Since this VTR becomes a playback-only unit when the
AJ-
23/24 Hz or 25 Hz (HD or SD) mode has been selected,
the functions relating to EE, recording and editing are all
set to the inhibited status. Neither is it possible to select
CTL in such a case.
(The related menus and function buttons are not
displayed, and operation is prohibited.)
For the instant when the tape begins to run at the 1k k
speed such as when it starts playing from the STOP
status, the image is disrupted and the sound is muted for
several frames because the tape is being synchronized
with the REF input.
The underlining (__) denotes the factory setting mode.
*DW:This is for SD outputs (during SD tape playback or down-
conversion outputs).
Description of setting
OFF:
Lock released (changes enabled)
ON:
Lock set (changes prohibited)
Advertisement
Table of Contents
