Video - Panasonic AJ-YA120AG Operating Instructions Manual

Setup menus

VIDEO

Item
Superimposed
No. No.
display
600 VIDEO IN SEL
0000
0001
0002
601 VIDEO INT SG
0000
0001
0002
0003
0004
0005
602 SDI IN MODE
0000
0001
603 V-MUTE SEL
0000
0001
0002
0003
604 FREEZE SEL
0000
0001
615 V OUT SEL
0000
0001
616 OUT MATRIX
0000
0001
620 DOWNCON
MODE 0000
0001
0002
621 UPCON V MODE
0000
0001
0002
626 D/C ENH H
0000
0001
627 D/C ENH V
0000
0001
" " indicates the factory setting.
Setting
Superimposed
display
For selecting the video signals to be input.
INTSG 0: The internal signal selected by VIDEO INT SG is generated.
HDSDI 1: The serial video signal supplied to the HD SDI IN connector is selected.
1394 2: The compressed digital signals supplied to the DV connector are selected.
When this happens, the audio input signals will also be supplied from the DV
connector (digital video interface).
<Notes>
O This item's setting cannot be changed while a tape is being played back.
O When 1394 is selected as this item's setting, "1080i" is selected as the menu
item No.630 [1080i>HD_OUT] setting and "720p" is selected as the menu item
No.632 [720p>HD_OUT] setting.
For selecting the type of internal signal.
100%CB 0: A 100% color bar signal is selected.
75%CB 1: A 75% color bar signal is selected.
SMPTE 2: An SMPTE color bar signal is selected.
BLACK 3: A black signal is selected.
PLL 4: The PLL signal is selected. (This signal is used for the adjustments performed
before the unit was shipped from the factory.)
EQ 5: The EQ signal is selected. (This signal is used for the adjustments performed
before the unit was shipped from the factory.)
For selecting how to process the serial input.
DR OFF 0: The 8 higher bits whose two lower bits have been rounded off are recorded.
DR ON 1: The dynamically rounded 8 higher bit signal is recorded.
For setting whether to mute the video output signal when a blank part of the tape is
detected during playback.
N MUTE 0: The video output signal is not muted. (It is frozen.)
GRAY 1: The video output signal is muted and turned gray.
BLACK 2: The video output signal is muted and turned black.
NOISE 3: The video output signal is muted and turned into noise.
For selecting the freeze mode of the still pictures and the slow play mode.
FIELD 0: Field freeze, field slow
FRAME 1: Frame freeze, frame slow
For selecting what signals are to be output from the VIDEO OUT1 output
connector.
CMPNT 0: The HD component signals are output.
CMPST 1: Composite signals are output.
For selecting what signals are to be output from the HD component output
connector.
YPbPr 0: The YP P
B
RGB 1: The RGB signals are output.
For setting the image processing during down-conversion.
FIT_V 0: Side cut mode
FIT_H 1: Letter-box mode
FIT_HV 2: Squeeze mode
For setting the image processing during up-conversion.
FIT_V 0: Side panel mode
FIT_H 1: Top and bottom cut-off in vertical direction
FIT_HV 2: Stretch mode
For enhancing the horizontal outlines during down-conversion.
0dB 0: 0dB
+1dB 1: +1dB
For enhancing the vertical outlines during down-conversion.
0dB 0: 0dB
+1dB 1: +1dB
Description of settings
signals are output.
R
43