Subscribe to Our Youtube Channel
Related Manuals for Yealink SIP-W52P
Summary of Contents for Yealink SIP-W52P
-
Page 1: Table Of Contents
Home PBXware SERVERware TELCOware SIPmon SIPProt Desktop & Mobile UADs Appliances From Bicom Systems Wiki Contents 1 Introduction 2 Requirements 2.1 Identifying phone model 2.2 Phone firmware 2.3 DHCP server 2.4 PBXware version 3 Installation 3.1 Power adapter 3.2 Power over Ethernet (PoE) 3.3 Find the phone IP address 3.4 Reset to factory settings 4 Registering phone... -
Page 2: Requirements
This User Guide is written as general guide on how to set up the Yealink phone model SIP-W52P to work with PBXware. Requirements Identifying phone model To start and successfully complete registration of your Yealink phone you need to know which phone model you will setup. -
Page 3: Dhcp Server
screen. Example: http://192.168.1.22. Login to phone web administration interface with your username and password. Please note, factory default login details are username: admin and password: admin. DHCP server Fully configured and operational DHCP server. PBXware version PBXware version In order to find out the PBXware version: Login to PBXware Navigate to Settings: About. -
Page 4: Find The Phone Ip Address
Enter PIN and press Done keysoft. Default factory PIN is 0000. Registering phone This chapter describes how to identify Yealink phone model, requirements that must be met and how to register the phone using manual configuration or auto provisioning. The following topics are covered:... - Page 5 UAD settings Navigate to Settings:UAD. Make sure Yealink UAD is enabled. To check the UAD status click on the edit icon corresponding to your Yealink phone. Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.
- Page 6 Enter the e-mail address associated with this extension. This e-mail address will receive all system notification messages. Example: john.smith@bicomsystems.com . Click on the Save button. Registering Phone This chapter describes how to register Yealink phone using Hostname or IP Address, or DNS SRV. The following topics are covered: Hostname or IP Address...
- Page 7 PBXware extension number. Example: 1003 Password The Secret of the extension as received in the e-mail associated with this extension. Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created extension. Sip Server Enter the Hostname or IP Address of the PBXware. - Example for Hostname: abc.bicomsystems.com - Example for IP Address: 192.168.1.10 Click on the Confirm button.
-
Page 8: Auto Provisioning
This chapter describes how to set UAD settings, create PBXware extension and register the phone using DHCP or Static IP address. NOTE: Auto Provisioning with DHCP or Static IP using HTTPS not supported for Yealink phone model SIP-T18P. The following topics are covered: UAD Settings Creating Extension... - Page 9 UAD settings Navigate to Settings:UAD. Make sure Yealink UAD is enabled. To check the UAD status click on the edit icon corresponding to your Yealink phone. Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.
- Page 10 Enter Yealink phone MAC address. Example: 0002FDFF1536. MAC address can be found at the back of the phone. Click on the Save button. Registering Phone This chapter describes how to register Yealink phone using DHCP, TFTP, HTTP & HTTPS or DNS SRV. The following topics are covered: DHCP TFTP or HTTP &...
- Page 11 Login to phone web administration interface If there is no DHCP in your network, you can still auto provision your Yealink phone. Please refer to your Yealink phone model User Guide for instruction about setting static IP address. After you configure your Yealink phone to use a static IP address, continue with the following steps.
- Page 12 In the URL field enter http:// or https:// followed by Hostname or IP Address, followed then by /tftp/ - Example for Hostname using HTTP: http://voip.bicomsystems.com/tftp/ - Example for Hostname using HTTPS: https://voip.bicomsystems.com/tftp/ - Example for IP Address using HTTP: http://192.168.1.10/tftp/ - Example for IP Address USING HTTPS: https://192.168.1.10/tftp/ Make sure you replace Hostname or IP Address from this example with your PBXware Hostname or IP address.
-
Page 13: Configure Blf
If there is no DHCP in your network, you can still auto provision your Yealink phone. Please refer to your Yealink phone model User Guide for instruction about setting static IP address. After you configure your Yealink phone to use a static IP address, continue with the following steps. -
Page 14: Etension Settings
Etension Settings 1. Login to PBXware web administration interface Open a new browser window and enter the IP address in order to access the PBXware web administration login page. Example: http://192.168.1.10. Login to PBXware with your e-mail address and password. 2. -
Page 15: Shared Parking
This chapter describes how to configure Shared Parking which is a feature that allows a person with a Yealink phone models SIP-T26P and SIP-T28P to pick up parked calls using BLF buttons. Once a call is parked, BLF button on the configured phone change it's color from green to red, indicating user about parked call. - Page 16 Login to PBXware with your e-mail address and password. 2. PBXware settings Navigate to Settings:Conf files. Make sure you are looking at extensions.con configuration file. Copy and past below code at the bottom of extensions.conf file. [hints] exten => 701,hint,park:701@parkedcalls exten =>...
Need help?
Do you have a question about the SIP-W52P and is the answer not in the manual?
Questions and answers