SAFETY INFORMATION Congratulations on your new Midea heat pump dryer. This manual contains important information on the installation, use and care of your appliance. Please read this manual carefully before use. Follow instructions and keep the manual for future reference.
Page 4
SAFETY INFORMATION 7. Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer. 8.
Page 5
SAFETY INFORMATION Electric Shock Hazard 1. Do not pull the power cord forcefully to pull out the mains plug. 2. Please do not plug/draw the mains plug with wet hands. 3. Do not damage the power cord and the power plug. Injury Danger 1.
TRANSPORT & INSTALLATION Transport Move cautiously. Do not grasp any salient parts of machine. The machine door can not be used as the handle for delivery. If the dryer can't be transported in upright position, tilt it to the right (container) side but not more than 30°. Installation Position 1.
ATTENTION & ADVICE Attention NOTE: The dryer should be left to stand still for at least 2 hours before it is connected to the power mains to allow the system to stabilize. Otherwise the heat pump could be damaged. 1. Before first use, please use the soft fabric to clean the inside drum. a) Put some clean rags into the drum.
IDENTIFYING PARTS OF THE DRYER Control panel Container Door Power cord Drum Filter door Air inlet Filter base Filter cover Hose holder External drainage hose External Drain Hose Installation The water container does not require to be emptied when water is externally drained. Step 2: Insert the external drainage hose.
QUICK START 1.Check if the container and filters have been cleaned up 2. Open the door and load the laundry 10.Unplug the power cord 3. Close the machine door 9. Clean the filters and empty container 4. Plug the power cord and 8.Press the 【...
PROGRAMME TABLE Weight Programme Application / Properties Delay (max) For cottons and coloureds made of cotton or linen. Extra To dry cotton pieces of clothing. Drying level: extra dry. Cotton Standard 7.0kg To dry cotton pieces of clothing. Drying level: cupboard dry. Iron To dry cotton pieces of clothing.
DRYING FUNCTIONS 1.【Delay】 With the delay function you can delay the programme start from 0 to 24 hours. When the programme starts, the delay start time begins to count down and the icon on the display blinks. Steps in details: (1).
Page 13
DRYING FUNCTIONS 5.【Lamp】 Use to turn the lamp on or off. When the lamp function is on, the lamp inside the drum will light up for 3 minutes when door is closed or the dryer is in operation, or 1 minute when the door is open. 6.【Signal】...
OPERATION INSTRUCTION Select the Programme 1. Press the【On/Off 】 key. When the LED display screen brightens up, rotate the programme knob to select the desired programme. 2. Select the【Delay】,【Time】,【Intensity】,【Signal】or【Anti-Crease】functions for additional option. 3. Press the【Start/Pause】key. Programme Start The drum will keep rotating after the programme starts, the status light in the display area will flash in sequence, the remaining time displayed will change automatically.
CLEANING & MAINTENANCE Always disconnect the clothes dryer from the mains power source before performing any maintenance Ÿ or cleaning of the appliance. For optimal performance, regular maintenance and cleaning is highly recommended. Ÿ Regular maintenance will extend the service life of the clothes dryer. Ÿ...
Page 16
CLEANING & MAINTENANCE Clean the Heat Exchanger If necessary, one time for each 2 months, remove the fluff from the heat exchanger compartment using the sponge or soft brush. When doing this, wear gloves. NOTE: The fluff can be removed more easily if it is first dampened e. g. with a laundry dampener.
If the clothes dryer does not perform as expected, malfunctions, or an alarm is sounding, please check the following list of possible solutions. If a solution cannot be found or the problem persists, please contact Midea service (refer to page 17). Do not, under any circumstance, dismantle the appliance yourself.
Please refer to the enclosed warranty card or visit www.mideaappliances.com.au for warranty information. Ensure you have the appliance model number and proof of purchase handy before calling Midea Customer Care to enquire about a warranty claim. Complete and retain the following information for your records: Model No.
SPECIFICATIONS Model MDHP07 Power supply 220-240V~ 50Hz Rated power 650W Refrigerant R134a Ambient temperature +5ºC ~ +35ºC Product dimensions (W x D x H) 595 x 622 x 845(mm) Rated drying capacity 7.0kg Net weight 53kg This dryer contains fluorinated greenhouse gases covered by the Kyoto Protocol. Hermetically sealed.