Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Midea MDA60-V012
Summary of Contents for Midea MDA60-V012
- Page 1 Tumble Dryer Machine Service Manual MDA60-V012/A0303-GB18...
-
Page 2: Table Of Contents
TABLE OF CONTENTS ….........…………………........SAFETY PRECAUTION …………………….……………………………………......1.1 Safety Precaution ………………….…………………………………………………......1.2 Warning ………………....…...…............2 OPERATIONAL ……………………………………..3.SCHEDULE OF FAILURE AND MAINTAIN TREE ……………………………....3.1 The Control panel not displayed after selecting the program ……………….………………………....... 3.2 The drum not worked after selecting the program ...……………….………………………...... -
Page 3: Safety Precaution
1.SAFETY PRECAUTION 1.1 Safety Precaution To prevent injury to the user or other people and property damage, the following instructions must be followed Incorrect operation due to ignoring instruction will cause harm or damage. Before service unit, be sure to read this service manual at first. 1.2 Warning Do not use a defective or underrated circuit breaker Use this appliance on a dedicated circuit. - Page 4 1.SAFETY PRECAUTION Do not plug or unplug the power supply plug during operation. There is risk of fire or electric shock. Do not touch (operation) the product with wet hands. There is risk of fire or electric shock. Do not place a heater or other appliance near the power cable. There is risk of fire and electric shock.
-
Page 5: Operational
3.SCHEDULE OF FAILURE AND MAINTAIN TREE 3.1 The Control panel not displayed after selecting the program Whether the power check the fuse socket has voltage or Turn on the Timer, check whether the wiring harness reliable the connection whether the voltage assemble well or not between electric shock is normal... -
Page 6: The Drum Not Worked After Selecting The Program
2.OPERATIONAL Symptom Check daily notice proceeding check that whether has power source or not; check that whether the power socket inserted firmly or not; Totally not worked Check that whether the power switch is on or not; Check that whether press the ”start/pause” button or not. Whether the power source stopped if the power source stopped , the program input could be canceled, it does not continue to work;... -
Page 7: Maintenance Non-Heating Malfunction
3.SCHEDULE OF FAILURE AND MAINTAIN TREE 3.3 Maintenance non-heating malfunction Whether to set up non- To choose the new program heating Whether the connect of Reliable connection heater、thermostat and PCB panel is well or not Whether the thermostat is Whether the heater is well well or not or not Change the thermostat... -
Page 8: Noise
3.SCHEDULE OF FAILURE AND MAINTAIN TREE 3.5 Noise Check the source of voice Whether the Screw which connect to Tub_wrap and lifter is twist the Screw loose,cause the Screw and Whether the Underprop_wheel adjust the axial position of Underprop_wheel Whether the Tub_shaft is break off Whether the Pulley Spring is change Pulley Spring... -
Page 9: Peculiar Smell Appears When The Dryer Is Working
3.SCHEDULE OF FAILURE AND MAINTAIN TREE 3.6 Peculiar smell appears when the dryer is working Whether something burning Clean heater in heater Solve the motor blocked , if Whether the motor blocked the motor damaged ，it Whether the belt sliding or Replace the belt wear leading to rubber odor Whether other electrical... -
Page 10: Phenomenon Of The Fault
4.PHENOMENON OF THE FAULT 4.1 The lamp of the control panel is showed ,when you press the power switch. Analysis and maintenance: 1.Check the power supply, whether power or socket contact undesirable. 2.Check the power wiring rack whether installed in place or not PCB board, see if the problem has been solved. 3.Check the line plug in the computer board, if it is normal, change into a new PCB board, see if the problem has been solved . -
Page 11: Switch On The Power Source, Press The "Start/Pause" Button, The Dryer Doesn't Work But Alarm
4.PHENOMENON OF THE FAULT 4.6 Switch on the power source, press the “start/pause” button, the dryer doesn't work but alarm. Analysis and maintenance: This might caused by the fault of door lock, make the PCB board detected that the door is open and alarmed, replace the door switch. -
Page 12: Disassembly Information For The Product
5.DISASSEMBLY INFORMATION FOR THE PRODUCT 5.1 Ordinary Information. 1.Please unplug the power cord when you disassemble or maintain the product; 2.Please use the regulation connector lug between the wires as much as possible. Then crimp them firmly by the proper tools and bundle them by the insulating tape; 3.When you plug the wires, please insert the plug to the bottom so it is not easily to be unplugged;... - Page 13 5.DISASSEMBLY INFORMATION FOR THE PRODUCT 2-2. Remove the power line 2-3. Remove the filter 3. remove the door component (including the door hinge) (1) remove the screws fixed door hinge; (2) take down the door component and hinge. 3-1. remove the door hinge,front door and back door frame 4.
- Page 14 5.DISASSEMBLY INFORMATION FOR THE PRODUCT 4-1. Remove the body of drum, lifting bar, heating pipe cover and drum shaft, etc 4-2. Remove the heating pipe, heating pipe cover and its support 5. Remove the control panel component (1) removed the screws fixed control panel component; (2) Pull out the terminals connected wire with PCB board.
- Page 15 5.DISASSEMBLY INFORMATION FOR THE PRODUCT 6-1. Remove the automatic thermostat 6-2. Remove the support components of the manual thermostat 6-3. Remove the manual thermostat 7. Remove the front plate assembly (1) remove the screws fixed front plate assembly; (2) take out the front plate assembly 7-1.
- Page 16 5.DISASSEMBLY INFORMATION FOR THE PRODUCT 7-2. Remove the support components of the drum 7-3. Remove the door gasket and front plate 8. Remove the side plates and base assembly (1) remove the screws fixed side plates; (2) take out the side plates and base assembly. 8-1.
- Page 17 5.DISASSEMBLY INFORMATION FOR THE PRODUCT 8-3. Remove the fixd block of the motor 8-4. Remove the fixd stator of the motor 8-5. Remove the tight spring 8-6.Take out the motor components 8-7. Remove the capacitance - 17 -...
-
Page 18: Notice
5.DISASSEMBLY INFORMATION FOR THE PRODUCT 8-8. Remove the motor bracket, Bottom plate and the air duct P1(white) Temperature sensor P2(brown) Door switch P3(purple) Motor P4(blue) Power cord P5(metal) Heating pipe P6(metal) Heating pipe 5.3 Notice 1.When you Remove the cabinet motherboard, pay attention to wear Gloves in case hurting your hands; 2.Do not rub the Cabinet in order not to influence its nicety;...