Samsung MH080FXEA4B Installation Manual page 2

WARNING

Stop the compressor before
disconnecting the refrigerant
pipe for pump-down
operation. If you disconnect
the refrigerant pipe while
compressor is operating with
service valve open, air inflow
will cause excessive pressure
in the refrigerant cycle that
could lead to explosion and
personal injury.
 Do not assemble the power
cord on your own, use two
cables together to extend
the cable length or tangle
the cable. Bad connection,
isolation and over voltage may
cause fire or electric shock.
CAUTION
 Perform the drainage/piping
work securely according to
the installation manual. If not,
water could drop from the
unit and household goods
could get wet and damaged.

Fasten a flare nut with a
torque wrench as specified
in this installation manual.
When fastened too tight,
a flare nut may break after
a long period of time and
cause refrigerant leakage.
 Wear thick gloves during the
installation process.
If not, personal injury
may occur due to the air
conditioner parts.
 Be careful not to touch
the outdoor unit inlet or
aluminium pins. You may get
personal injury.
 The air conditioner should be
used only for the applications
for which it has been
designed: the indoor unit is
not suitable to be installed in
areas used for laundry.

When installing the indoor
unit, use a stable stool and
watch your steps carefully.
 To prevent injury when
accidentally touching the
indoor unit fan, install the
indoor unit at least 2.5m
above the floor level.
FJM_IM_DB98-31792_E_6.10.10.indd 3
 Hazards or unsafe practices that may result in severe personal injury or death.

Make sure to turn off the
main power when setting
up the indoor unit electrical
circuit or power cords. There
is a risk of electric shock.
 Make sure that proper
circuit breaker and safety
switches are installed.
Install a ground leakage
breaker depending on the
installation place(where it is
humid). If not, it may cause
electric shock.
 Hazards or unsafe practices that may result in minor personal injury or property
damage.
 Our units must be installed in
compliance with the spaces
indicated in the installation
manual to ensure either
accessibility from both sides
or ability to perform routine
maintenance and repairs. The
units' components must be
accessible and that can be
disassembled in conditions
of complete safety either for
people or things.
For this reason, where it is
not observed as indicated
into the Installation Manual,
the cost necessary to reach
and repair the unit (in safety,
as required by current
regulations in force) with
slings, trucks, scaffolding or
any other means of elevation
won't be considered
in-warranty and charged to
end user.
 Do not install the outdoor
unit in a place where
animals could live. If an
animal get contact with the
electric parts, damage or
fire may occur. In addition
ask the customer to
maintain a clean installation
place around it.
 Check the unit for damage
that may have taken place
during transportation and do
not install or use damaged
equipment.

Do not install the unit by
yourself (owners). Incorrect
installation of the unit could
cause injury due to fire,
electric shock and water
leakage or from the unit
falling. Consult a dealer or a
qualified installer.
 Use the unit on a single
outlet circuit. Do not share
the power outlet with other
appliances.
Obtain the consent by a
qualified installer before
connecting the unit to the
power supply system.
 After completing the
installation run the trial
operation. If no error occurs,
explain to the customer
how to use and clean the air
conditioner according to the
user's manual. In addition
give the installation manual
and the user's manual to the
customer.
 All of the manufacturing
and packaging material
used for your new appliance
are compatible with the
environment and can be
recycled.

Dispose of the packaging
material in accordance with
the local requirements.

This product is an air
conditioning system and
contains a coolant that must
be recovered and disposed
of in an appropriate way by
qualified personnel. At the
end of the life cycle, take
it to a proper recycling or
disposal center or return it to
the dealer so that it can be
disposed correctly.
3
E-
2010-6-10 9:53:14