1. Manuals
  2. Brands
  3. Weidmuller Manuals
  4. Network Router
  5. IE-SW-VL09T-6TX-3SC
  6. Hardware installation manual

Weidmuller IE-SW-VL09T-6TX-3SC Hardware Installation Manual

Value line
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
Ethernet Switch – Value Line
IE-SW-VL09T-6TX-3SC (Unmanaged)
Hardware Installation Guide
First Edition, December 2010
124098_0000/00/12.10
This document and any further product information -
if available - can be downloaded at the internet link:
http://www.weidmueller.com/downloads
Copyright Notice
Copyright © 2010 Weidmüller Interface GmbH & Co. KG
All rights reserved.
Reproduction without permission is prohibited.
Please note:

Advertisement

Table of Contents
loading

Related Manuals for Weidmuller IE-SW-VL09T-6TX-3SC

Summary of Contents for Weidmuller IE-SW-VL09T-6TX-3SC

  • Page 1 Ethernet Switch – Value Line IE-SW-VL09T-6TX-3SC (Unmanaged) Hardware Installation Guide First Edition, December 2010 124098_0000/00/12.10 Please note: This document and any further product information - if available - can be downloaded at the internet link: http://www.weidmueller.com/downloads Copyright Notice Copyright © 2010 Weidmüller Interface GmbH & Co. KG All rights reserved.

  • Page 2: Package Checklist

    Overview The switch IE-SW-VL09T-6TX-3SC with 9 Copper-and 3 SC-Fiber-Ports provides an economical solution for your Ethernet connections. As an added bonus, the built-in smart alarm function helps system maintainers monitor the health of your Ethernet network. This Ethernet switch has a wide operating temperature range of -40 to 75°C, and is designed to withstand a high degree of vibration and shock.
  • Page 3 Panel Layout of IE-SW-VL09T-6TX-3SC IE-SW-VL09T-6TX-3SC Front Panel Grounding screw Terminal block for power inputs PWR1/PWR2 and relay output Heat dissipation orifices DIP switches Power input PWR1 LED Power input PWR2 LED Fault LED 10/100BaseT(X) Port TP port’s 100 Mbps LED TP port’s 10 Mbps LED...

  • Page 4: Mounting Dimensions (Unit = Mm)

    Mounting Dimensions (unit = mm) DIN-Rail Mounting The aluminum DIN-Rail attachment plate should already be fixed to the back panel of the Ethernet Switch when you take it out of the box. If you need to reattach the DIN-Rail attachment plate, make sure the stiff metal spring is situated towards the top, as shown in the figures below.

  • Page 5: Wall Mounting (Optional)

    Wall Mounting (optional) For some applications, you will find it convenient to mount the device on the wall, as illustrated below. STEP 1: Remove the aluminum DIN-Rail attachment plate from plate the switch’s rear panel, and then ⇒ attach the wall mount plates, as shown in the diagram below.

  • Page 6: Wiring Requirements

    c. A 4mm conductor must be used when connect ion to the external grounding screw is utilized. d. PROVISIONS SHALL BE MADE, EITHER IN EXTERNAL TO THE APPARATUS, TO P REVENT THE RATED VOLTAGE BEING EXCE EDED BY THE TRANSIENTS DISTURBANCES OF MORE THAN 40 %.

  • Page 7: W Iring The Alarm Contact

    You can use the type of signal transmitted through a wire to determin hich wires should be kept sepa rate. The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together. eep input wiring and output wiring separated. is strongly advised that you label wiring to all devices in the system wh cessary.

  • Page 8: Communication Connections

    DC power source voltage is stable. Communication Connections The switch IE-SW-VL09T-6TX-3SC has 6 10/100BaseT(X) Ethernet ports, and 3 100BaseFX (SC/ST-type connector) fiber ports. 10/100BaseT(X) Ethernet Port Connection The 10/100BaseT (X) ports located on the Ethernet Switch front panel are used to connect to Ethernet-enab led devices.

  • Page 9: 100Basefx Ethe Rnet Port Connection

    Switch Port Cross-Over Cable Switch Port (NIC Port) (NIC Por 45 Plug Pin 1 RJ45 RJ45 Connector Cable Wiring Conne ctor (Rx+) (Tx+) (Rx-) (Tx-) (Tx+) (Rx+) (Tx-) (Rx-) 100BaseFX Ethe rnet Port Connection he concept behind the SC/ST port and cable is quite straightforward. Suppose ou are connecting devices I and II.

  • Page 10: Dip Switch Settings

    Switch is set to ON is not properly connected. If neither of these two conditions occurs, the Fault circuit will be closed. DIP Switch Settings 4 5 6 7 ON: Enables the corresponding PORT Alarm. If the port’s link fails, the relay will form an open circuit and the fault LED will light up.

  • Page 11: Fiber Ports

    pay attention to the type of Ethernet cable being used for the connection. This means that you can use either a straight-through cable or cross-over cable connect IE-SW-VL09-Switches to other Ethernet devices. Fiber Ports Fiber switched ports operate at a fixed 100 Mbps speed and full-duplex mode to provide the best performance.

  • Page 12: Switching And Address Learning

    Switching and Address Learning IE-SW-VL09-Switches have an address table that can hold up to 1K node addresses, which makes i t suitable for use with large networks. The address tables are self-learning, s o that as nodes are added or removed, or moved from one segment to another, the Ethernet switches automatically keeps up with new node locations.

  • Page 13: Specifications

    (Core/Cladding) μm 50/125 9/125 9/125 (1 dB/km, 800 MHz × km) Power Input Voltage 12 to 48 VDC, redundant inputs Input Current @ 24VDC IE-SW-VL09T-6TX-3SC: 0.35 A Connection Removable “6-pin” Terminal Block Overload Current IE-SW-VL09T-6TX-3SC: 1.6 A Protection Reverse Polarity Present...

  • Page 14: Contact Information

    Regulatory Approvals Safety UL60950, UL 508, CSA C22.2 No. 60950, EN60950 Hazardous Lo cation UL/cUL Class I, Division 2, Groups A, B, C and D ATEX Class I, Zone 2, Ex nC nL IIC T4 FCC Part 15, CISPR (EN55022) class A EN61000- 4-2 (ESD), Level 3 EN61000...

Table of Contents