Advertisement
A
INSTALLATION.
PANEL MOUNTING
1. Cut a 152mm hole through the panel. (Suitable for existing holes up to 185mm).
2. Remove the Indoor Grille [A]. Loosen the screw (top middle) of the Grille, to release front grille gently lever the
Grille downwards away from the Inner Cover [B].
3. Remove Inner Cover [B]. Loosen the screw (bottom middle) and release the inner grille gently from the Base
Housing [D].
4. Remove the Cable Grommet [C], pierce/cut a hole in the Grommet to suit the cable size, maintaining the
integrity of the seal and replace the grommet in the Base Housing to suit either a top or back cable entry.
5. Slide the Base Housing into the hole in the panel and secure into position using screws and fixings provided.
Fig. 1.
6. Ensure the fan blade rotates freely.
7. Select and follow the appropriate wiring diagram in Section B WIRING.
8. Replace the Inner Cover and Indoor Grille (retightening the screws securely).
9. Switch the mains power supply on and check the fan is operating correctly.
WALL MOUNTING
1. Cut a 152mm hole through the wall and insert the wall sleeve [E] with the larger diameter sleeve on the room
side and cement both ends into position flush with the wall faces. The wall sleeve should be angled downwards
away from the fan to allow any condensation to drain to the outside wall.
2. Remove the Wall Mounting Plate from the Outside Grille [F] to use as a template, mark the fixing hole centres
on the wall. Drill and plug the wall and fix the Wall Mounting Plate into position (screws provided).
3. Fix the Outside Grille [F] back onto the Wall Mounting Plate. Ensure the louvres are pointing downwards.
4. Remove the Indoor Grille [A]. Loosen the screw (top middle) of the Grille, to release front grille gently lever the
Grille downwards away from the Inner Cover [B].
5. Remove Inner Cover [B]. Loosen the screw (bottom middle) and release the inner grille gently from the Base
Housing [D].
6. Remove the Cable Grommet [C], pierce/cut a hole in the Grommet to suit the cable size, maintaining the
integrity of the seal and replace the grommet in the Base Housing to suit either a top or back cable entry.
7. Slide the Base Housing into the Wall Liner and secure into position using screws and fixings provided (Fig. 1.).
8. Ensure the fan blade rotates freely.
9. Select and follow the appropriate wiring diagram in Section B WIRING.
10. Replace the Inner Cover and Indoor Grille (retightening the screws securely).
11. Switch the mains power supply on and check the fan is operating correctly.
WINDOW MOUNTING
1. Cut a 152mm hole in the glass (Suitable for existing holes up to 185mm).
2. Ensure that the glass surfaces are clean and free from grease.
3. Remove the Indoor Grille [A]. Loosen the screw (top middle) of the Grille, to release front grille gently lever the
Grille downwards away from the Inner Cover [B].
4. Remove Inner Cover [B]. Loosen the screw (bottom middle) and release the inner grille gently from the Base
Housing [D].
5. Remove the Cable Grommet [C], pierce/cut a hole in the Grommet to suit the cable size, maintaining the
integrity of the seal and replace the grommet in the Base Housing to suit a top cable entry.
6. Fit required spacers behind the fan back plate, engaging the locating pips. Place the fan spigot through the
hole in the glass from the inside, with a gasket on each side of the glass.
7. From the outside, place on the remaining spacer, with the locating pips facing outwards. For double-glazing
and materials up to 40mm thick, one or more spacers may be discarded. (Fig. 2.)
8. Draw the assembly together with the threaded fixing ring. Do not over-tighten.
9. Fix the Outside Grille [F] on to the Spacers (screws provided). Ensure the louvres are pointing downwards.
10. Ensure the fan blade rotates freely.
11. Select and follow the appropriate wiring diagram in Section B WIRING.
12. Replace the Inner Cover and Indoor Grille (retightening the screws securely).
13. Switch the mains power supply on and check the fan is operating correctly
FIXING HOLES
3
Advertisement
