Advertisement
Main Menu
(continued)
VIDEO CONFIG
Sub menu
Settings
GAMMA
<NORMAL>
*2
SELECT
<FILM>
*2
<VARICAM>
FILM GAMMA
<OTHER>
COLOR TEMP.
<USER0–63>
<D93>
<D65>
<D56>
<VAR1>
<VAR2>
<VAR3>
SHARPNESS
<HIGH>
*2
<LOW>
MODE
*2
<0–30>
SHARPNESS H
*2
<0–30>
SHARPNESS V
*2
<MODE2>
I-P MODE
<MODE1>
*2
<OFF>
MONO
<ON>
*2
<OFF>
ANAMO
<ON>
*2
<4:3>
SD ASPECT
<16:9>
*2
<NORMAL>
SCAN
<UNDER>
*2
<OFF>
NOISE WIPE
<ON>
*1 Even if FILM gamma is changed during 2 screen display, only the main window is set, and the changes are not
reflected in the sub window.
*2 When "RGB-COMP." is selected in "YP
*3 The following sharpness values can each be set,
1) VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW,
SHARPNESS H/V : 0)
2) any other input line's HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0)
3) any other input line's SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
and the setting values for the selected input signal from within this group is displayed. The adjustment status is
displayed in the bottom right when selected.
*4 When "VAR1", "VAR2" or "VAR3" is selected, the monitor switches to WB adjustment mode (
*5 When selecting USER0–63
1) Push [ENTER] (USER changes to blue).
16
Explanation
Used to select the gamma curve.
*1
When FILM is selected,
left of the screen.
Used to select the type of FILM gamma mode.
<VARICAM> VARICAM use
<OTHER>
*5
Used to select the color temperature.
<USER0–63>
<D93>
<D65>
<D56>
<VAR1>
<VAR2>
<VAR3>
*3
Used to select the width of the sharpness edge.
<HIGH>
*3
Used to set the sharpness in the horizontal direction.
When adjusting, the item display moves to the lower part of the
screen.
*3
Used to set the sharpness in the vertical direction.
When adjusting, the item display moves to the lower part of the
screen.
Used to set the mode for IP change.
<MODE2>
Used to switch between color and monochrome (MONO).
<OFF> Color
* When this is ON, the picture adjusting knob [CHROMA] setting
is fixed at 0.
If an Anamo lens has been used on the camera, and input through
SDI 720/60P, 59.94P, the picture is resized to Anamo size
magnification. (a vertically compressed signal can be amplified
vertically and corrected when it is displayed.)
Used for setting the aspect ratio settings when using SD signal
input.
<4:3>
Used to set under-scan and normal display.
<NORMAL>Normal display
<OFF> This makes a fluid and smooth contrast obtainable.
<ON>
P
/RGB" in the "INPUT SELECT" menu (
B
R
The underlined values are factory preset setting values.
When using other types than VARICAM
Adjustable settings 0–63 (color temperature
around 3000K–9300K)
Color temperature around 9300K
Color temperature around 6500K
Color temperature around 5600K
WB adjustment mode
WB adjustment mode
WB adjustment mode
Thin edge
<LOW>
Within Field
<MODE1>
<ON>
4:3 display
<16:9>
<UNDER>Under-scan
This is especially effective for continuously changing the contrast
of the source signal or CG signal when the S/N is very high.
Noise reduction mode. Depending on the camera, this mode
can be especially effective for dark scenes. We recommend
leaving this setting "ON" under normal conditions.
2) Select 0–63 with [
mark is displayed in the top
*4
*4
*4
Thick edge
Normal mode
Monochrome
16:9 display
page 21), this does not operate.
page 17).
,
], and push [ENTER].
Advertisement
