Messages - Panasonic DMR-ES15M Operating Instructions Manual

Messages

On the television
Cannot finish recording
completely.
Cannot play.
Cannot record on the disc.
Unable to format.
Please check the disc.
Cannot record. Disc is full.
Cannot record. Maximum
numbers of titles exceeded.
No disc
Please change the disc.
This is a non-recordable disc.
This disc is not formatted
properly.
5
On the unit's display
The following messages or service numbers appear on the unit's display when something unusual is detected during startup and use.
SET
(" " stands for a number.)
HARD ERR
("HARD" and "ERR" are
alternately displayed.)
NoREAD
NoWRIT
NoERAS
PLEASE WAIT
("PLEASE" and "WAIT" are
alternately displayed.)
UNSUPPORT
("UNSUP" and "PORT" are
alternately displayed.)
UNFORMAT
("UNFOR" and "MAT" are
alternately displayed.)
U59
U61
U88
U99
• The program was copy-protected.
• The disc may be full.
• The maximum number of times you can record the program is exceeded.
• You inserted an incompatible disc (Discs recorded in PAL video, etc.).
• The disc may be dirty or scratched.
• Create space by deleting any unnecessary titles.
(Even if you delete recorded content from DVD-R, DVD-R DL, +R or +R DL, there is no
increase in disc space.)
• Use a new disc.
• The disc may be upside down.
• There may be a problem with the disc. Press [; OPEN/CLOSE] on the main unit to remove it
and check it for scratches or dirt. (The unit turns off automatically after you open the tray.)
• The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R,
DVD-R DL, DVD-RW (DVD-Video format), +R, +R DL or +RW.
• You inserted an unformatted DVD-RAM, DVD-RW, +R, +R DL or +RW. Format the disc with
this unit.
• The operation is prohibited by the unit or disc.
• The remote control and main unit are using different codes. Change
the code on the remote control.
Press and hold [ENTER] and the indicated number button at the
same time for more than 2 seconds.
• If there is no change after turning the unit on and off, consult the dealer where the unit was
purchased.
• The disc is dirty or badly scratched. The unit cannot record, play, or edit.
• The message may appear when the DVD lens cleaner has finished cleaning.
Press [; OPEN/CLOSE] on the main unit to eject the disc.
• Recording may be unavailable due to a disc problem. Use a new disc.
• Deleting an item may be unavailable due to a disc problem. Use a new disc.
• Displayed when the unit is started. This is not a malfunction.
• The unit is carrying out its recovery process. You cannot operate the unit while "PLEASE
WAIT" is displayed.
• You have inserted a disc the unit cannot play or record on.
• You have inserted a new DVD-RW/+R/+R DL/+RW or a DVD-RAM/DVD-RW (DVD-Video
format) recorded on other equipment.
• The unit is hot.
The unit switches to standby for safety reasons. Wait about 30 minutes until the message
disappears.
Select a position with good ventilation when installing the unit. Do not block the vent on the
rear of the unit.
• There was a power failure or the AC plug was disconnected while the unit was on. The unit is
carrying out its recovery process. This process restores the unit to normal operation. The
unit is not broken. Wait until the message disappears.
• There was something unusual detected with the disc while recording or playing. The unit is
carrying out its recovery process. This process restores the unit to normal operation. The
unit is not broken. Wait until the message disappears.
• The unit fails to operate properly. Press [POWER 8] on the main unit to switch the unit to
standby. Now press [POWER 8] on the main unit again to turn the unit on.
RAM -RW(V) +RW
Page
—
—
—
—
6
29, 33, 34
—
—
6
4
34
—
15
—
6
—
—
—
—
—
4, 5
34
—
—
41
—
RQT8314
39