Flex LD 15-10 125 R Original Operating Instructions page 21

LD 15-10 125 R / LD 15-10 125
Continuous operation with engaged switch
rocker:
 Push the switch rocker forwards and
engage by pressing the front end.
NOTE
cçääçïáåÖ=~=éçïÉê=Ñ~áäìêÉI=íÜÉ=ëïáíÅÜÉÇ=çå=
éçïÉê=íççä=ÇçÉë=åçí=êÉëí~êíK
Switch off the machine:
 To switch off the power tool, release the
switch rocker by pressing the rear end.
Using a dust extraction system
klqb
fí=áë=êÉÅçããÉåÇÉÇ=íç=ìëÉ=~=cibu=`ä~ëë=j=
Çìëí Éñíê~ÅíçêK
 Connect extraction hose to the 32 mm
connector.
 Engage extraction hose in hose support.
 Connect extraction hose to the dust
extraction system. Follow the operating
instructions for the dust extraction system!
Check the attachment! If required, use an
appropriate adapter.
klqb
fÑ=óçìê=Çìëí=Éñíê~Åíçê=êÉèìáêÉë=~=ëéÉÅá~ä=
ÅçååÉÅíáçå=EáKÉK=~=ÅçååÉÅíáçå=çíÜÉê=íÜ~å=íÜÉ=
PO ããLPS ãã=ëí~åÇ~êÇ=ÅçååÉÅíáçå=ïÜáÅÜ=
áë áåÅäìÇÉÇ=ïáíÜ=íÜÉ=ÉäÉÅíêáÅ=éçïÉê=íççäFI=
Åçåí~Åí=óçìê=Çìëí=Éñíê~Åíçê=ëìééäáÉê=íç=çÄí~áå=
íÜÉ=~ééêçéêá~íÉ=~Ç~éíÉêK
Working with the power tool
t^okfkd>
qÜÉ=êçí~íáåÖ=ë~åÇáåÖ=ÇáëÅ=ãìëí=åçí=ÅçãÉ=áåíç=
Åçåí~Åí=ïáíÜ=ëÜ~êé=éêçàÉÅíáåÖ=çÄàÉÅíëK=a~åÖÉê=
çÑ=âáÅâÄ~Åâ>=a~ã~ÖÉ=íç=ë~åÇáåÖ=é~ÇK=fÑ=íÜÉ=
ë~åÇáåÖ=é~Ç=áë=Ç~ã~ÖÉÇ=çê=ëÉîÉêÉäó=ïçêåI=
áí ãìëí=ÄÉ=êÉéä~ÅÉÇK
`^rqflk>
eçäÇ=íÜÉ=ÉäÉÅíêáÅ=éçïÉê=íççä=ïáíÜ=ÄçíÜ=Ü~åÇë>=
1. Attach sanding tool.
2. Connect dust extraction system.
3. Insert mains plug.
4. Switch on dust extraction system.
5. Switch on the device.
6. Place the renovation sander on the work
surface.
The brush ring (LD 15-10 125 R) or the
rubber extraction ring (LD 15-10 125)
must be flush with the work surface.
21