Table of Contents
Advertisement
Reference Standards
In the United Kingdom, the installation and initial start-up of the
boiler must be by a CORGI registered installer in accordance with
the installation standards currently in effect, as well as with any
and all local health and safety standards i.e. CORGI.
In the Republic of Ireland the installation and initial start-up of
the appliance must be carried out by a Competent Person in
accordance with the current edition of I.S.813 "Domestic Gas
Installations" and the current Building Regulations, reference
should also be made to the current ETCI rules for electrical
installation.
The installation of this appliance must be in accordance with
the relevant requirements of the Local Building Regulations,
the current I.E.E. Wiring Regulations, the by-laws of the local
authority, in Scotland, in accordance with the Building Standards
(Scotland) Regulation and Health and Safety document No. 635,
"Electricity at Work Regulations 1989" and in the Republic of
Ireland with the current edition of I.S. 813 and the Local Building
Regulations (IE).
C.O.S.H.H.
Materials used in the manufacture of this appliance are non-
hazardous and no special precautions are required when
servicing.
Codes of Practive
Installation should also comply with the following British
Standards Code of Practice:
BS 7593:1992
Treatment of water in domestic hot water
central heating systems
BS 5546:1990
Installation of hot water supplies for
domestic purposes
BS 5440-1:2000
Flues
BS 5440-2:2000
Air supply
BS 5449:1990
Forced cicrulation hot water systems
BS 6798:2000
Installation of gas fired hot water boilers
of rated input not exceeding 70kW
BS 6891:1989
Installation of low pressure gas pipes up to
28mm
BS 7671:2001
IEE Wiring Regulations
BS 4814:1990
Specification for expansion vessels
BS 5482:1994
Installation of L.P.G.
and in the Republic of Ireland in accordancce with the following
codes of practice:
I.S. 813
Domestic Gas Installations
Avoid installing the boiler where the air inlet can be polluted by
checmical products such as chlorine (swimming pool area), or
ammonia (hair dresser), or alkalin products (launderette).
Flue
Detailed information on flue assembly can be found in the
"Connecting the Flue" section.
The boiler must be installed so that the flue terminal is exposed
to the free passage of external air at all times and must not
be installed in a place likely to cause nuisance. It must not be
allowed to discharge into another room or space such as an
outhouse or closed lean-to.
Condensing boilers have a tendency to form a plume of water
vapour from the flue terminal due to the low temperature of
the flue gasses. The terminal should therefore be located with
due regard for the damage or discolouration that may occur to
Supplied By www.heating spares.co Tel. 0161 620 6677
building within the vicinity and consideration must also be given
to adjacent boundaries, openable windows should also be taken
into consideration when siting the flue.
The minimum acceptable clearances are shown below:
- A Directly below an opening, window, etc
- B Horizontally to an opening, window, etc
- C Below gutters, soils pipes or drain pipes
- D Below eaves
- E From vertical drain pipe or soil pipe
- F From internal or external corner
- G Above ground, roof or balcony level
- H From a surface facing the terminal
- I From a terminal facing a terminal
- J Vertically from a terminal on the same wall
- K Horizontally from an terminal on the same wall
- L Fixed by vertical flue terminal
N
: t
ote
he
flue
must
Not
be
iNstalled
NuisaNce
aNd
positioNed
to
eNsure
discharge
across
a
bouNdary
It may be necessary to protect the terminal with a guard, if this is
the case it will be necessary to purchase a stainless steel terminal
guard. Reference should be made to the Building Regulations
for guidance.
Ventilation
The room in which the boiler is installed does not require
specific ventilation. If the boiler is installed in a cupboard or
compartment ventillation is not required for cooling purposes.
Gas Supply
The gas installation and tightness testing must be in accordance
with the requirements of BS6891. Ensure that the pipe size is
adequate for demand including other gas appliances on the
same supply.
Electrical Supply
The appliance requires an earthed 30V - 50 Hz supply and
must be in accordance with current I.E.E. regulations. It must
also be possible to be able to completely isolate the appliance
electrically. Connection should be via a 3 amp douple pole fused
isolating switch with contact separation of at least 3mm on both
poles. Alternatively, a fused 3 Amp, 3 pin plug and unswitched
socket may be used, provided it is not used in a room containing
a bath or shower, it. It shoild only supply the appliance.
installation
300 mm
300 mm
75 mm
00 mm
75 mm
300 mm
300 mm
500 mm
500 mm
1500 mm
300 mm
iN
a
place
likely
to
cause
a
that
products
of
combustioN
do
Not
9
Advertisement
Table of Contents
