Noise Characteristics; General Information; Technical Data - Toolson DWS225DC Operating Manual

Manufacturer
scheppach Fabrikation
von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
89335 Ichenhausen
Germany

Technical Data

Dimensions LxWxH (mm)
Disc diameter (mm)
Revolutions grinding wheel min.
(1/min)
Revolutions grinding wheel max.
(1/min)
Length suction hose (mm)
Weight kg
Power unit
Motor V/Hz
Rated power P1 (W)

Noise characteristics

Sound power level LWA
Sound pressure level LpA
Uncertainty in measurement K
Vibration
Uncertainty in measurement K
Note:
The measured noise levels are determined according to
EN 60745.
Use hearing protection!
The measured total vibration values (triax vector sum)
are determined according to Standard EN 60745.
The vibration level specified in this data sheet has
been measured according to the standard test stated
in Standard EN 60745, and it is used to compare the
different devices.
The level can be used for an initial exposure
assessment. The specified vibration level applies to the
most important applications of the device. However,
if the device is used for other applications with other
accessories or if it is used in a badly maintained
condition, the vibration level can deviate from the
specifications. This means that the exposure level
may increase significantly during the course of the
operational hours.
An estimation of the vibration exposure also needs to
include the times during which the device is switched
off or it is switched on but not in use. This means that
the exposure level may decrease significantly during
the course of the operational hours.
Additional safety measures must be taken to protect
the operator from the impact of the vibrations. This
includes: Maintaining the device and accessories;
keeping hands warm; organising work patterns.
380x260x260
215
1500
3000
1500
3,4
230/50
1200
dB(A) 97,6
dB(A) 86,6
dB(A) 3
m/s² 2,356
m/s² 1,5
lntended use
The intended use of this power tool is the sanding of
large areas of drywalls as a preparation before pain-
ting or wallpapering using suitable abrasive sheets.
This power tool is neither suited for the preparation of
small areas, corners and edges, nor for the removal
of wallpaper and the grinding of ceilings and wet grin-
ding.
Do not use the power tool for cutting or roughing or
polishing. Do not use it together with wire brushes. Do
not treat asbestos containing materials with this power
tool.
This power tool is solely intended for private use. Da
not use the power tool for any other purpose than for
the intended one. Any other use beyond the intended
use is im proper.
For any resulting darnage or injury, the user/Operator
is held liable, not the manufacturer.

General Information

• After unpacking, check all parts for possible trans-
portation damages. In the event of complaints, inform
the supplier immediately. Any complaints made after
this time will not be accepted.
• The shipment is to be checked for completeness
upon receipt.
• Read through the manual carefully in order to make
yourself familiar in dealing with the device before
using it for the first time.
• Only use original equipment regarding accessories,
as well as consumable items and spare parts. Spare
parts can be obtained from your specialized dealer.
When ordering, please specify our part numbers, as
well as type and construction year of the device.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advantage
of its application possibilities in accordance with the
recommendations. The operating instructions contain
important information on how to operate the machine
safely, professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and how to
increase reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regulati-
ons that apply for the operation of the machine in your
country. Keep the operating instructions package with
the machine at all times and store it in a plastic cover
to protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only be
operated by persons who were instructed concerning the
operation of the machine and who are informed about