Table of Contents
Advertisement
Monogram
36" Built-In Bottom-freezer Refrigerator
®
FLUSH INSET INSTALLATION 1/2" PANELS
35 1/2"
(90.2)
26 3/16"
(66.5)
6"
ELEC.
Flush inset depth
(15.2)
20 13/16"
(52.9)
Depth to cleat
10"
(25.4)
Finished cleats
85"
(215.9)
WATER
3 1/2"
5"
5"
3 1/2"
(9.0)
(12.7)
(12.7)
(8.9)
3 1/2"
W
FRONT VIEW
SIDE VIEW
ANTI-TIP BRACKET
81 1/2"
(207.0)
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
ZIC360NXRH
5 3/8"
(13.7)
3"
(7.6)
1 1/2"
(3.8)
1/2" Panel
3/4"
(1.9)
Width of side cleats
75"
(190.5 )
From floor
to bottom
of electrical
84"
area
(213.4)
height
to cleat
(17.8)
(8.9)
SIDE VIEW
FLUSH INSTALLATION
Use two
additional hole
ZIC360NHLH_RH
locations at end
of brackets
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
TOP VIEW
Case
Finished cleats
Case Trim
24"
(61.0)
7/16"
(1.1)
Door
Trim overlap
1/2"
39"
(99.1) Flush inset width
37 1/2"
(95.3)
Width between cleats
A
6"
ELEC.
(15.2)
10"
24 3/16"
(25.4)
(61.4)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
B
10"
(25.4)
7"
7"
WATER
3 1/2"
(17.8)
3 1/2"
WATER
(9.0)
(8.9)
FRONT VIEW
C
L
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
Ensure holes
selected are
centered on
the studs
Wall
Studs
FLUSH INSET INSTALLATION
NOTES
A Mounting the junction box in this
location will also allow for front
accessibility through access panel.
(1.3)
B Water supply area.
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
The information below applies to all
installation constructions:
• A wall bracket, bolts and toggles will
be supplied with the unit.
• The bolts will be used to attach bracket
to wall in 4 locations. Two of the
locations must penetrate the center of
the wall studs.
• The toggles are used for stability in
drywall and when metal studs are
encountered. Lag bolts are used in
wood studs.
• In installation opening, measure 82"
from floor and draw a horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two studs
have their centerlines within the center
32.5" of installation opening to ensure
2 wall studs are penetrated.
• The bracket will be centered left to
right in opening with bottom of bracket
on the horizontal line.
• When unit is placed in opening, the
bracket tabs will align with openings
in back of the unit. The unit will be
secured to the bracket using supplied
"L" bolts.
See Installation Instructions for
detailed instructions.
Product Specification Revised 5/16
ZIC360NHRH
Advertisement
Table of Contents
