Regency Horizon HZ54E Owners & Installation Manual page 23

Description
Attic Insulation Shield 12"
Basic Horizontal Termination Kit (A)
Horizontal Termination Kit (B)
Vertical Termination Kit
High Wind Vertical Cap
High Wind Horizontal Cap
Horizontal Square Termination Cap
Vertical Termination Cap
Storm Collar
Adjustable Flashing 0/12-6/12
Adjustable Flashing 6/12-12/12
Vinyl Siding Standoff
Vinyl Siding Shield Plate
Snorkel Termination 14"
Snorkel Termination 36"
Restrictor Disk
Colinear Flex Connectors
FPI
946-604/P Simpson Direct Vent or Astro Cap -Vent Guard (Optional)
770-994 Rigid Pipe Adaptor (Must use with all rigid piping)
**946-606 Starter collar reducer 5" x 8" to 4" x 6-5/8"
**Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).
** Not available/applicable for the following units: B41XTE, B41XTCE, HZ54E
Offset Pipe Selection: Use this table to determine offset pipe lengths.
Pipe Length 5" x 8" Venting
(L)
Run (X)
0" (0mm) 5-11/16" (144mm)
6" (152mm) 8-13/16" (224mm)
9" (229mm) 10-15/16" (278mm)
12" (305mm) 13" (330mm)
24" (610mm) 21-7/16" (697mm)
36" (914mm) 29-13/16" (757mm)
48" (1219mm) 38-1/4" (972mm)
Regency Fireplace Products . 6988 Venture St. . Delta, BC . Canada . V4G 1H4 . 604-946-5155 . www.regency-fi re.com
Simpson
Direct Vent Pro ®
58DVA-IS
N/A from FPI
N/A
58DVA-KHA
58DVA-VHA
58DVA-VCH
N/A
N/A
N/A
58DVA-SC
58DVA-F6
58DVA-F12
58DVA-VSS
N/A
58DVA-SNK14
58DVA-SNK36 (N/A - FPI)
58DVA-RD
N/A
Rise (Y)
15-5/16" (389mm)
18-7/16" (468mm)
20-9/16" (522mm)
22-11/16" (576mm)
31-1/16" (789mm)
39-7/16" (1002mm)
47-7/8" (1216mm)
Selkirk
Direct Temp™
N/A N/A
5DT-HKA N/A
5DT-HKB N/A
5DT-VKC N/A
N/A N/A
N/A N/A
5DT-HHC 5DHT
5DT-HVC 5DVT
5DT-SC 5DSC
5DT-AF6 5DF
5DT-AF12 5DF1-2
5DT-VS 5DVS
5DT-VSP N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
946-623/P
**946-506/P
946-625
For specifi c instructions on venting components - visit the
manufacturers website listed below.
Simpson Direct Vent Pro: www.duravent.com
Selkirk Direct-Temp: www.selkirkcorp.com
Metal-Fab Sure Seal: www.mtlfab.com
Industrial Chimney Company: www.icc-rsf.com
Note: Horizontal runs of vent must be level, or have a 1/4"
rise for every 1 foot of run towards the termination.
Never allow the vent to run downward - this could cause high
temperatures and may present a possible fi re hazard.
Regency Horizon
installation
ICC Excel
Metal-Fab™
Direct
Sure Seal
N/A
TM-5HTK
TM-5HTK
N/A
TM-5VT
TM-5DHT
TM-5HT
N/A
TM-SC
TF-5FA
TF-5FB
TM-VSS
N/A
TM-5ST14
TM-5ST36
TM-5DS
N/A
AstroCap XL Horizontal Cap
Vent Guard (Optional)
Vinyl Siding Standoff - AstroCap XL
® HZ54E-10 Gas Fireplace
|
23
| 23