Panasonic CQ-VD7500U Operating Instructions Manual page 30

MENU: Audio Settings (for VD7700U)
E
N
G
L
I
S
H
Menu
48
LARGE
SP SETUP
for large speakers, when bass
(continued)
playback is possible (at least
100 Hz or lower)
SURROUND
SMALL
(Surround speaker setting)
for small speakers, or when
bass playback is not possible
when not using surround
speakers
SUB • W
when using a subwoofer
(Subwoofer speaker setting)
A subwoofer (option, CJ-SW38 recom-
when not using a subwoofer
mended) is required. A power amplifier
(option) is also required for connecting
a subwoofer.
Setting range: –12 dB to +12 dB
SP LEVEL
Default: ± 0 dB for all speakers
(Speaker Level)
(Adjusting the output balance of each
A test signal (a continuous tone) is
speaker)
output from each speaker for
FRONT L
approximately two seconds.
Adjust the output balance so that
(Left front speaker output balance)
the tone appears to have the same
CENTER
volume from each speaker.
(Center speaker output balance)
Adjusting the output balance:
FRONT R
Adjust the volume of all of the other
speakers to the volume level of the
(Right front speaker output balance)
speaker from which the test signal
R SURROUND
¡ appears to be the quietest.
¡If the speaker setting is "NONE" or
(Right surround speaker output bal-
"NO" for a speaker, the test signal
ance)
is not output and that speaker
L SURROUND
¡ cannot be selected.
¡Turn [VOLUME] or press [}] or
(Left surround speaker output balance)
[{] (VOLUME) to adjust the vol-
SUB W ume of the test signal.
¡
(Subwoofer speaker output balance)
64
CQ-VD7700U/VD7500U
Setting Value Operations
:
Panel
SURROUND a NONE
or
LARGE
:
Remote
NONE :
[ } ] or [ { ] []] or [[]
a
a [ENTER]
default: LARGE
YES :
Panel
SUB • W a NO
NO :
Remote
[ } ] or [ { ]
a []] or [[]
default: NO
a [ENTER]
Panel
(1 dB steps)
q Touch the image of the speaker you
want to set.
[
w
: UP
]
: Down
Touch to select
(a page 63)
Remote
q [}] or [{]
w [[] : UP
[]] : Down
(continued)
: Previous menu
: Exit
SP DELAY
(Speaker Delay)
or SMALL
(Adjusting the timing with which the
audio from each speaker reaches the
listener's position)
CENTER
(Center speaker delay time setting)
SURROUND
(Surround speaker delay time setting)
¡Make this adjustment while listening
to sound.
or YES
¡If the speaker setting is "NONE" for a
speaker, that speaker cannot be
selected. (a
VTR LEVEL
(Setting the VTR (VTR1/VTR2) input
Level)
Make this setting if it is not possible to
adjust the volume through the con-
nected device (on the output side).
Note: This setting is adjustable for an
external device that is connected to
VTR1 or VTR2. (e.g. VCR)
Menu Setting Value
Setting range:
Center speaker...
0 ms to 5 ms (1 ms steps)
Surround speakers...
0 ms to 15 ms (1 ms steps)
1 ms = 0.001 seconds
Default: 0 ms for all speakers
page 63)
Lower Higher
–6 dB –4 dB –2 dB
± 0 dB +2 dB +4 dB
+6 dB
: Input level
default: ±0 dB
Notes:
¡If the input level from
VTR1/VTR2 is too high, the
audio will not be output nor-
mally. Adjust the input level
so that "OVER" does not
appear.
¡After setting the input level
The volume can be adjusted
by turning the volume knob or
pressing [}] or [{] (VOL-
UME) on the remote control.
E
N
G
L
I
: Previous menu S
H
: Exit
Operations
49
Panel
q Touch a speaker image. (Center or
Surround)
[
w : Long
]
: Short
Remote
q [}] or [{]
w [[] : Long
[]] : Short
Panel
]
: Lower
[
: Higher
Remote
[]] : Lower
[[] : Higher
65
CQ-VD7700U/VD7500U