Table Of Contents; Job Specification Sheet - Pentair FLECK 5800 SXT Service Manual

TABLE OF CONTENTS

JOB SPECIFICATION SHEET .................................................... 2
INSTALLATION ......................................................................... 3
START-UP INSTRUCTIONS ...................................................... 4
CONTROL FEATURES .............................................................. 4
USER PROGRAMMING ............................................................. 5
CONTROL OPERATION ............................................................. 6
MASTER PROGRAMMING MODE CHART ................................ 7
MASTER PROGRAMMING MODE ............................................. 8
VIEWING DIAGNOSTIC DATA .................................................... 12
SYSTEM DISINFECTION ........................................................... 13
INSTALLATION CHECKLIST ..................................................... 13
CARE AND USE OF YOUR BRINE TANK................................... 13
TROUBLESHOOTING ................................................................ 14
POWERHEAD ASSEMBLY......................................................... 15
5800 CONTROL VALVE ASSEMBLY .......................................... 16
TURBINE METER ASSEMBLY - P/N 60626 ............................. 17
PADDLE METER ASSEMBLY - P/N 60086-50 .......................... 17
BYPASS VALVE ASSEMBLY (METAL) ........................................ 18
BYPASS VALVE ASSEMBLY (PLASTIC) ..................................... 18
SAFETY BRINE VALVE .............................................................. 19
WATER CONDITIONER FLOW DIAGRAMS ............................... 20
DIMENSIONAL DRAWINGS ...................................................... 22
INJECTOR FLOW DATA ............................................................. 23
IMPORTANT PLEASE READ:
• The information, specifications and illustrations
in this manual are based on the latest information
available at the time of printing. The manufacturer
reserves the right to make changes at any time
without notice.
• This manual is intended as a guide for service
of the valve only. System installation requires
information from a number of suppliers not known
at the time of manufacture. This product should be
installed by a plumbing professional.
• This unit is designed to be installed on potable
water systems only.
• This product must be installed in compliance with
all state and municipal plumbing and electrical
codes. Permits may be required at the time of
installation.
• It is established that when daytime water pressure
exceeds 80 psi (5.5 bar), the maximum pressure
rating of 125 psi (8.6 bar) can be exceeded. A
pressure regulator must be installed on this
system or warranty is voided.
• Do not install the unit where temperatures may
drop below 32°F (0°C) or above 125°F (52°C).
• Do not place the unit in direct sunlight. Black
units will absorb radiant heat increasing internal
temperatures.
• Do not strike the valve or any of the components.
• Warranty of this product extends to manufacturing
defects. Misapplication of this product may result
in failure to properly condition water, or damage to
product.
• A prefilter should be used on installations in which
free solids are present.
• In some applications local municipalities treat
water with Chloramines. High Chloramine levels
may damage valve components.
• Correct and constant voltage must be supplied to
the controller to maintain proper function.
2 • FLECK 5800 SXT Upflow/Downflow

JOB SPECIFICATION SHEET

Job Number: ___________________________________________________
Model Number: _________________________________________________
Water Hardness: _______________________________________ ppm or gpg
Capacity Per Unit: _______________________________________________
Mineral Tank Size: ______________ Diameter: ________ Height: _________
Salt Setting per Regeneration: _____________________________________
Regenerant Flow: Upflow
1. Meter Size:
A. 3/4" Paddle Wheel
B. 3/4" Turbine
C. 1" Paddle Wheel (Not Used)
D. 1" Turbine (Not Used)
E. 1-1/2" Electronic Inline Plastic Turbine (Not Used)
F. 1-1/2" Paddle Wheel (Not Used)
G. 2" Paddle Wheel (Not Used)
H. Generic_________Pulse Count__________Meter Size__________
2. System Type:
A. System #4: 1 Tank, 1 Meter, Immediate, or Delayed Regeneration
B. System #4: Time Clock
3. Control Program Settings:
A. Backwash: ____________________________________ Minutes
B. Brine and Slow Rinse: ___________________________ Minutes
C. Rapid Rinse: ___________________________________ Minutes
D. Brine Tank Refill: _______________________________ Minutes
E. Pause Time: ___________________________________ Minutes
F. Second Backwash: ______________________________ Minutes
4. Drain Line Flow Control:_____________________________ gpm
5. Brine Line Flow Control: ____________________________ gpm
6. Injector Size#: ___________________________________
CALIFORNIA PROPOSITION 65 WARNING
This product contains chemicals known to the
WARNING:
State of California to cause cancer or birth
defects or other reproductive harm.
Downflow