Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for XVision Pro HD
Summary of Contents for XVision Pro HD
-
Page 2: Table Of Contents
XC Camera Setup and OSD Guide Contents Safety Precautions ........................... 2 Introduction ............................3 Recap ............................... 4 Live View ..............................4 PTZ Setting ............................6 System Setup Tab ............................ 7 Device info ............................7 PTZ Settings ............................8 Display Settings ........................... 9 Encoding ............................ -
Page 3: Safety Precautions
XC Camera Setup and OSD Guide Safety Precautions Do not install the equipment in an environment with too much moisture, dust or smoke dust as this may result in fire or electric shock. In the unlikely event that the equipment should malfunction and emit an abnormal smell or smoke, please immediately stop it, shut off the power and contact your supplier. -
Page 4: Introduction
XC Camera Setup and OSD Guide Introduction This guide is for the Xvision Pro HD XC Range of IP Cameras OSD Browser Guide. It is recommended that the units are setup and tested before being mounted or installed. These instructions are for guidance only detailed information is in accordance with the product. -
Page 5: Recap
XC Camera Setup and OSD Guide Recap Once you have set the IP address, amended the Active X controls and installed them, viewed the XC IP camera on the Browser, you can now go through all the menu options. Navigate back to your XC device, http://192.168.1.100 that we previously setup. - Page 6 XC Camera Setup and OSD Guide Voice intercom：Connect to audio on the device) if supported) on the audio input port and active loudspeaker on the audio out port, then click the talkback icon. Turn on the voice intercom switch and the icon shows as , the talkback between PC and IP camera can be performed.
-
Page 7: Ptz Setting
XC Camera Setup and OSD Guide PTZ Setting PTZ setting: Set the preset, cruise, tracking, etc. Shown below. Preset setting: Adjust the camera to the appointed angle and location through directional buttons, and then select a preset number on the preset drop down list, click to set it. -
Page 8: System Setup Tab
XC Camera Setup and OSD Guide System Setup Tab Device info Device Name: Edit the camera name Device Sn: Display the IPC Sn Device Type: Display the IPC type Serial No. : Display the product serial No. ... -
Page 9: Ptz Settings
XC Camera Setup and OSD Guide PTZ Settings Protocol: Support Pelco D，Pelco P，Pelco F protocol Address: 0-255 adjustable Baud Rate: Baud rate selectable Operation method: Connect analog high speed dome at the IP camera AB port, set the protocol and baud rate, and control the high speed dome through IPC preview interface After all parameter settings are completed, click “Save”... -
Page 10: Display Settings
XC Camera Setup and OSD Guide Display Settings Name: Modify the appointed channel name Main stream OSD: 12pt/18pt/24pt/36pt/48pt Sub stream OSD: 12pt/18pt/24pt Time Format: Select different time display mode for the appointed channel Date Format: Select different date display mode for the appointed channel ... -
Page 11: Encoding
XC Camera Setup and OSD Guide Encoding Compress type: Primary Stream (Normal) / Sub Stream selectable Stream: Including complex stream/ video stream two types Resolution: Depending on the resolutions supported this field will have different values. Frame Rate: Set different frame rate for channel ... -
Page 12: Video Parameters
XC Camera Setup and OSD Guide Video Parameters Day & Night Mode: Outside Trigger/ Auto/ Color/ Black White four kinds of mode selectable. Non infrared IP cameras default mode is Auto, and infrared IP cameras default mode is Outside Trigger. ... -
Page 13: Motion Detection
XC Camera Setup and OSD Guide Gamma: CURVE_1_6，CURVE_1_8,CURVE_2_0,CURVE_2_2 totally four modes, default is CURVE_2_0 Anti-Flicker: Auto, 50hz, 60hz, the default is Auto After all parameter settings are completed, click “Save” these settings will take immediate effect. Motion Detection ... -
Page 14: Video Tampering
XC Camera Setup and OSD Guide Preset: Alarm input to link the preset. Snap Interval: Set the snapshot interval time Snap Count: Set the snapshot count in every second After all parameter settings are completed, click “Save” these settings will take immediate effect. -
Page 15: Privacy Mask
XC Camera Setup and OSD Guide Preset: Alarm input to link the preset. Snap Interval: Set the snapshot interval time Snap Count: Set the snapshot count in every second After all parameter settings are completed, click “Save” these settings will take immediate effect. -
Page 16: Network Settings
XC Camera Setup and OSD Guide Network Settings IPV4: IP protocol IPV6: IP protocol Static IP: The device IP address is permanent, manual input. DHCP: When you enable DHCP your router’s DHCP server will get an IP address from your router automatically ... -
Page 17: Management Platform
XC Camera Setup and OSD Guide Management Platform * For future Management applications. -
Page 18: Multicast Config
XC Camera Setup and OSD Guide Multicast Config Default value is disabled for multicast config. After you "Enable Multicast", users can set IP address/port/TTL of the primary stream video, sub stream video, primary stream audio, and sub stream audio. -
Page 19: Ddns Settings
XC Camera Setup and OSD Guide DDNS Settings DDNS is implemented through a dynamic domain resolution server. You will need to setup an account through a DDNS provider, some are listed below. This is used when you do not have a Static IP address from your Broadband provider. -
Page 20: Ntp Settings
XC Camera Setup and OSD Guide NTP Settings Enable NTP: Click enable use NTP Server Address: Input NTP server IP address NTP Port: Only TCP transmission supported, default is 123 Adjust time interval: Input the interval time ... -
Page 21: Email Settings
XC Camera Setup and OSD Guide Email Settings You will need to confirm the following details from your Email provider or your network Administrator. (sent)Email Address: Input the address of the outbox Password: Input the password of the outbox ... - Page 22 XC Camera Setup and OSD Guide FTP Settings Please contact your FTP Server supplier or your network Administrator for more information on how to use the FTP feature. Enable: Click to enable the FTP service Server Address: Input the upload server address ...
-
Page 23: Alarm Input
XC Camera Setup and OSD Guide Alarm Input Alarm Input: Select the alarm input number Alarm In Name: Input alarm input name Trigger: Select the alarm statue: Normal Open/ Normal Close Alarm Schedule: Alarm schedule can be set from Monday to Sunday... -
Page 24: Alarm Output
XC Camera Setup and OSD Guide Email: Click Email, then the IPC will send an Email to the appointed mailbox when an alarm is triggered Snap: Click Snap, snapshot the current image picture when alarm triggered Record: Click, video will be recorded automatically when alarm triggered ... -
Page 25: Exception Settings
XC Camera Setup and OSD Guide Exception Settings Exception Type: Disk full/ disk fault/ network broken/ IP address conflict/ Illegal access/ video signal exception types selectable Record: Click Record, video will record as any exception when the type is triggered ... -
Page 26: System Update
XC Camera Setup and OSD Guide System Update Updates will be available through Xvision, you can also contact your please of purchase for more information. File: Click Browse to find and select the upgrade kit, then click Update. Note; only the network administrator should apply firmware updates, please check with your supplier before applying any updates. -
Page 27: Restore
XC Camera Setup and OSD Guide Restore Restore: Restore to factory setting Reboot: Reboot the devices Local Settings Window Mode: Set the preview window mode(Full/ 4:3/ 16:9 ) Preview Capture: Select the preview capture file storage path ... -
Page 28: File Management Tab
XC Camera Setup and OSD Guide File Management Tab Search: Select the search start time, click button, the video record and snap image file will display( Double click the file to check details) Start: Click button to play the backup video image file ... -
Page 29: Log Tab
XC Camera Setup and OSD Guide Log Tab Main Type: All/ Alarm/ Exception Settings/ Operation/ Additional Information four types selectable Start Time: Set the start time End Time: Set the end time Page Num: Set the log numbers on each page ... -
Page 30: Ip Camera Network Ports
XC Camera Setup and OSD Guide IP Camera Network Ports The default network ports of IP camera are: Web port Communication port, audio/video 5050 data transmission port, talkback data transmission port 5050 Audio/video data transmission port Multi-cast port 28080 Onvif port 8000 RTSP port RTSP port... -
Page 31: Default Network Parameters
XC Camera Setup and OSD Guide Default Network Parameters Cabled Network: IP Address: 192.168.1.188 Data Port: 5050 Subnet mask: 255.255.255.0 Web port： 80 Gateway: 192.168.1.1 DHCP: OFF 1. No video image displayed in IE browser. Possible reason: ActiveX not installed Solution: ActiveX must be installed when visiting IP camera for the first time via Internet Explore. - Page 32 XC Camera Setup and OSD Guide Solution: Stop the connection between IP camera and Network, connect up IP camera to PC separately using a cross over cable, reset IP address according to the proper operations recommended. Possible reason 3: IP addresses are in different subnets. Solution: Check IP address, subnet mask address of the IPC and the settings of Gateway/router.
- Page 33 XC Camera Setup and OSD Guide...
Need help?
Do you have a question about the Pro HD and is the answer not in the manual?
Questions and answers