Table of Contents
Advertisement
control prompts which appear on the LCD
display.
(11)
WHEEL CONTKOLLER/ SLIDER
VOLUME
This
is the
DXi
masiter
volume control
BALANCE
This adjusts the volume balance between
channels A and
3.
PORTAMENTO
This adjusts the portamento
tirr.e.
*
When
the
FUMCTION mode PORTAMENTO PEDAL
U
KNOD ASSIGN
is
OFF,
portamento will
not
function.
^P.36
PITCH
This
is the
pitch bend wheel,
*
This will not function
when
the
k
FUNCTION moae PITCH
BEaiD
RANGE parameter
P
is set to
0.
^P.36
MODULATION
This controls LFO modulation.
That
is,
the
depth
of
vibrato, tremolo and wow effects.
*
When the
FUNCTIOI]
mode MOD
IJHEEL
ASSIGN
is set to EBC
(EG
BIAS CONTROL) this
functions
as
a
volume
or
brilliance
control,
-"p.as
*
Modulation will
not
function when
the
EDIT mode AMPLITUDE MODULATION
SENS,
parameter
is
set to
0,
and
the
PITCH
MODULATION
SENS,
parameter
is set to
,^p.27
*
This
v/ill
not
function when
the
FUNCTION mode MOD
V7HEEL
SENSITIVITY
parameter
is set to
or
when
the
MOD
WHEEL ASSIGNS are
all OFF,
^P.38
2-3
Connection
Terminals
The following types
of
connection terminals
^re
provided:
1.
AUDIO OUTPUT
2.
CONTROL CONNECTOR
3.
MIDI
CONNECTOR
Please connect
the
power cord, amplifier,
peripheral equipment and accessories
correctly,
as
shown
in the
illustration.
The
connector terminals
are
provided
in two
locations:
on the
rear*
panel
(fig, 9a),
and
to the
lower left
of
the
keyboard
(fig. 9b).
(1)
AUDIO OUTPUT
OUTPUT
(fig. 25a)
Audio outputs
A,
B
and
P
are provided.
Both
unbalanced phone jack and balanced XLR type
connectors are provided
for each output,
for
a
total
of
6
audio output connectors.
This
is the
output
for
tone
generator
output channel A (memory
A)
.
However,
when
the
KEY ASSIGN
rX)DE
is
set to
single, either channel A or
B,
whichever
is in use,
will
be
simultaneously output from this
jack.
This
is the
output
for
tone
generator
output channel
B
(memory
B)
.
However,
when the KEY ASSIGN
1X3
DE is
set
to
single, either channel
A or
B,
whichever
is in use,
will
be
simultaneously output from this
^ack.
P
(PR0GRAr4)
This output provides
a
monaural
rr:ix
of
channels
A
and
B.
It is
normally
ON,
The FUNCTION mode
PROGR/iH
OUTPUT ASSIGN
function
can be used to independently
turn channels A and
B
on
or
off as
required
for this output.
-/>.J7
*
The unbalanced phone jack outputs are
for
connection
to
reproduction
ecjuipment
with unbalanced type inputs.
In
order to
appreciate
the
extremely
broad dynamic range
of
the DXI we
recommend
the use
of a
high-performance
keyboard amplifier
or
integrated
PA
amplifier/speaker
system.
*
The
balanced XLR
type
connectors are
intended mainly
for use in
professional
applications where
noise must be kept
to an
absolute minimum.
These
teririnals
should
be
used
in
sound
reinforcement and recording situations.
*
The output level
at
outputs
A,
B
and
P
is
controlled
by the
FUNCTION mode
OUTPUT
Lt:VEL
ATTENUATE parameter.
If
the
OUTPUT LEVEL ATTENUATE parameter
is
set to
0,
no
sound will
be output,
PHONES
(fig.
9b)
This jack accepts virtually
any
standard
pair
of
headphones.
It
outputs
a
mono mix
of the
channel A and
B
signals.
PHONE VOLUME
(fig.
9b)
This controls
the level
of the
headphones.
The
PHONES volume control controls headphone
volume independently
from
the
main volume
slider control.
(2)
CONTROL CONNECTORS
VOLUME
(fig.
9a)
This connector permits foot control
of
volume level.
An FC-3A foot controller can
be
connected
here.
*
In
this case the
volume slider control
should
be
set
to its
maximum
setting,
MODULATION
(fig.
9a)
This connector
perir.its
foot control
of the
depth
of
LFO modulation
(vibrato, tremolo,
wow)
and EG bias (volume, brilliance).
An
FC-3A foot controller
can be
connected
here.
*
The foot controller will not function
Advertisement
Table of Contents
