Yamaha DX1 Owner's Manual page 38

Fig. 66.
LFO
Modulation Control Function
MODULATION WHEEL
FOOT CONTROL
BREATH CONTROL
AFTER TOUCH
Each
of
the four controllers can regulate effects such as tremolo, vibrato, wow, etc.
Also, data setting can
be
carried
out separately by all four controllers.
connecteo to the
rear-panel MODULATION
connector.
*
Pressing
the pedal down
increases the
depth
of
the effect.
Job
1
- MOD. VJHEEL
SENSITIVITY
i
0—15
Sets the depth
of the
effect applied with
the
MODULATION WHEEL.
*
The Qata range
is
—
15, At the
MODULATION
V7HEEL
is OFF, At 15 maximuin
effect variation
ib
achieved.
* The
LCD display will read "FUNCTION 6A
MWS>>iiVJA>>FCS>>FCA
riodulation
wheel
sensitivity
(0-15) XX". '"XX" is the
data.
*
If
the
EDIT
raocie
AHPL.
MODULATION
SENSITIVITY master parameter is set to
for all
operators, AMPLITUDE
MODULATION
(tremolo, wow) and EG BIAS
(brilliance, expression) will not
function. Also
if
the
EDIT mode
PITCI.
MODULATION SENS.
master parameter is
set to
0,
PITCH MODULATION (vibrato)
will not function.
-^P.27
Job
2
- MOD,
WHEEL ASSIGN
EBC. AMD. PMD
Selects
the
effect to be
controllea by the
MODULATION WHEEL.
PITCH MODULATION,
AiiPLITUDE
MODULATION
or
EG
BIAS can
oe
selected,
*
The selected function is
inoicatea
oy
a
3-digit display (0=OFF, 1=0N)
.
From
the left digit
to
the right:
EDC
(EG
BIAS CONTROL), AMD (AMPLITUDE
MODULATION
DEPTH)
,
PMD (PITCH
MODULATION DEPTH). For
example "001"
indicates that EBC and AMD are OFF,
while PMD
is ON.
*
;;hen
EDC
is ON
and AMPL. MODULATION
SENSITIVITY
is
greater than
1,
applied
to
a
mociulator the
result is
brilliance
control, and
applied
to
a
carrier
the
result is
volume (expression) control,
*
When PMD
is ON
and PITCH MODULATION
SEr:S.
is
greater than
1,
vibrao
control
is
possible,
* l,;hen
AMD
is OM
and AMPL.
I'ODULATIOi^
is
greater than
1,
applied
to
a
carrier
the
result
is
trei.iclo
contrcl, anu
applied
to
a
modulator
the
result
is
wow control,
*
More than one effect can be selected at
a
time.
Pressing
the
DATA ENTRY YE3
button consecutively results
in the
following selection sequence:
OOO-^CiOl-OOlC-^Oim)
100=M01-MIC-^111.
Pressing the
DATA ENTRY NO button
reverses this sequence.
* The
LCD display
will read "FUNCTION
6
>>MWS«BMWA»FCS»FCA
Mod,
wheel
assign
(EBC.
AMD, PMD) XXX". "XXX" is
the
effect selection data as describea
above.
Job
3
-
FOOT CONT.
SENSITIVITY
0—15
Sets the depth
of
the effect
applied witn
the FOOT CONTROLLER.
*
The data range is
0—15.
At the FOOTJ
CONTROLLER is OFF, At 15
maxiruur;.
effect variation is achieved,
*
The LCD display will reaa "FUNCTION
6
>>MWS>>MV;aBBFCS>>FCA Foot controller
sensitivity (0-15) XX".
"XX" is the
data,
*
If
the
EDIT mode AMPL.
MODULATION
SENSITIVITY master parameter is set to
for ell
operators, AMPLITUDE
MODULATION
(tremolo, wow) and EG
BI/vS
(brilliance, expression) will not
function. Also
if
the EDIT
mode PITCH
MODULATION SENS,
master parameter is
set to
0,
PITCH MODULATION (vibrato)
vjill
not
function.
JOD
4
- FOOT CONTi
ASSIGN
EBC. AMD. PMD
Selects the effect
to be
controlled
by
the
FOOT CONTROLLER.
PITCH
iiODULATION,
AMPLITUDE MODULATION
or
EG
BIAS can oe
selected.
* The
selected tuncticn
is
inoicated
by a.
3-digit display
(0=OFF, 1=0N)
.
From
\
the
left digit
to
the right:
EBC
(EG
BIAS CONTROL), AMD (AMPLITUDE
MODULATION
DE1>TH)
,
PMD (PITCH
MODULATION
DEPTH)
*
The
EBC,
AMD and PMD effects are the
same as Job
2 - MOD,
WHEEL ASSIGN,
*
More than
one
effect
can oe
selected at
a tiiae.
Pressing the
DATA ENTRY
YES
button consecutively results in the
following selection sequence:
000->G01->01C->011->100->101->11C->111.
Pressing the
DATA ENTRY NO button
reverses this sequence,
*
The LCD display will read "FUNCTION
6/^
>>MUS>>MVjA>>FCSBBFCA Foot control
r
assign
(EBC, AMD. PMD) XXX' CX" is
the
effect selection data as described
above.
If
a
foot controller
is not
connecteo
ana tnc
EDIT moae AMPL.
MODULATION
SENSITIVITY parameter is set to
3
for
all
carriers, ana the
FOOT CONT.
ASSIGN
EBC is
ON,
ano FOOT CONT.
SENSITIVITY
is
set to
15,
no
souno will be
output.
38