Yamaha DX1 Owner's Manual page 20

*
I:
Replacing an Original VOICE MEMORY
(fig.
23)
In
order
to
re-store edited data
in
tVie
original memory locationr use the STORE ALL
function
(the
VOICE MEMORY and
PERFORMAi-TCE
MEMORY
are
simultaneoulsy re-stored
in their
original locations),
*
Using
the STORE ALL function
it is
not possible
to
move
data
to
another
memory location, move data from one
channel
to
another,
or
move
data from
the
internal memory
to an external
cartridge.
*
The STORE ALL function makes it possible
to
store internal VOICE MEMORY data
back into the same internal memory
location, or to store cartridge memory
data back into the same cartridge
memory location.
^P.53
(j)
In
order to defeat the memory protect
function, switch to
the FUNCTION
mode,
(k)
Call the protect memory write
function.
(1)
When
the LCD display
reads "Internal
memory write protect
ON",
press
the
DATA ENTRY NO
key,
causing
the
display
to read "Internal memory write protect
OFF". This defeats the memory protect
function.
*
If
you attempt
a
store operation with
the
memory write protect function
ON,
the
"**ERROR**
IV-protectedl
"
message
will
be
displayed and storing will
not
be
possible.
*
The STORE VOICE function
can be used
if
PERFORMAI>ICE
MEMORY data has
not been
changed.
(m) If
the store switch
is
used
to
enter
the
STORE mode,
the
"STORE ALL FROM
>>
CURRENT EDITING
TO
>>
CURRENT SELECTED"
message will
be displayed.
VJith
the
STORE ALL function
the store position
selection process
is greatly shortened.
(n)
Press the DATA ENTRY
YES button
to
begin
the
store operation.
*
Both channels
A and
D
cannot
be
stored
at the same time. The store operation
must
be
performed
on one channel at
a
time,
*
After
the store operation
be sure to
turn
the
VOICE MEMORY
or
RAH cartridge
memory protect function back
on.
Fig,
23.
Replacing Original Voice Memory,
(1)
FUCTIuN
14E
HFRT::>rLF' i/ELMK
I f ,
+
e
r
t;
^1 ns
m o
r-
y P
r o t
e
-l
t
OFF
CZ3
CO CD
f
t
(q)
(n)(o)(P)
r
t t
(k) (J)
N(r)
.TOPE
FFOM:
ri.ippEHT
FEPFuPMhlHr
L
rij.-
INT
.
pi
1
STORE
hLL
FROM>
:
CURRENT EDITING
T - C
LI
P
R E H
T
SELECTED
*
II:
Storing
in
a
New VOICE MEMORY
or
PERFORMANCE MEMORY
(fig. 24)
In order to store in
a
new
VOICE MEMORY
or
PERFORtJVNCE MEMORY position,
the STORE VOICE
function
(the
store function which permits
movin9 VOICE MEMORY data
to
a
new memory
location) is used.
In
addition the STORE
PERF0RI:A1jCE
function must
be used.
The STORE
PERFORMANCE function
is
the
function which
permits
movinc;
PERFORMANCE MEMORY data
to
a
new memory location.
*
To store
to
a
new position in
a
RAM
cartridge,
or to
store from
a
ROM
or
RAM cartridge
to the
internal memory
(single load) insert the cartridge into
the DXl and press the
CARTRIDGE
switch.
*
If a
PERFORMANCE MEMORY CARTRIDGE
is
used the "**ERROR** Cartridge format
conflict!" message
will be
displayed
when the CARTRIDGE switch
is
pressed.
*
To store from the internal memory to
a
RAM cartridge (single
save) insert the
cartridge into
the
cartridge slot
and
turn the CARTRIDGE switch OFF.
(j)
Switch
to the
FUNCTION
mode.
^
(k)
Call the protect memory write
-,
^^
function.
--I{j)
—
(i)
(1)
Press the DATA ENTRY section
NO
button.
(m)
Switch
to
the STORE mode and press the
DATA ENTRY NO switch Causing
the
"STORE
VOICE FROM
>>
EDITING XXXX TO
»
INT
Al-1 xxxx" nessage to
be
displayed.
*
"INT- Al-1" is the memory position,
and
"XXXX"
is the
voice
name,
(n)
The VOICE MEMORY and bank 2nd voice
switches are then used to set the store
destination.
The destination position
is
displayed following
"TO" on the LCD
display.
*
When storing from
a
cartridge into the
internal memory select the
destination
location after the
CARTRIDGE switch has
been turned OFF,
* Uhen storing from the
internal memory
to
a
RAH cartridge, select the
destination
location after
the
CARTRIDGE switch has
been turned ON,
^^
*
If a
PERFORIJ^NCE
MEMORY CARTRIDGE
is
^k
used,-
the
"**ERROR** cartridge format
^
conflict!"
message
v/ill
appear when
the
cartridge switch
is
pressed,
(o)
Pressing the DATA
ENTRY
YES
button
begins
the actual store operation.
* Store voice
can only
be
performed on one
channel at
a
time.
After performing
the store operation on one channel.
Fig. 24, Storing New Voice and Performance
Memory
STORE
FRON>>ED[T]Hij
y.XK'^'^
UOICE
T0>> INT.
fil-1
XXXX
20