Table of Contents
Advertisement
Thii^
Decs
use
in the
above state
the
foot controller
is set
up
to be
a
volume control, and must
be
pressed
to
produce sound output.
(7)
BANK
7
(F7)
Tnis
deteru.ines the
operation
of the
BREATH
COHTROLLER and AFTER TOUCH, and incorporates
tlie
4
jobs—
BRTII
COUT.
SENSITIVITY, DRTH
CONT, ASSIGN,
AFTER TOUCH SENSITIVITY, and
AFTER TOUCH ASSIGU.
*
In
the DXl, the
BREATH CONTROLLER and
AFTER TOUCH can
be
used
to
apply
vibrato
(pitch modulation)
,
tremolo
{carrier amplitude modulation), wow
(modulator amplitude modulation)
effects using LFO
niodulaticn,
and
brilliance (modulator
EG BIAS)
or
volume (carrier
EG
BIAS)
control
(fig. 66).
*
The BCl BREATH
COHTROLLER
is
a
mouthpiece
type
device which controls
the
appropriate effect according
to the
air
pressure (breath pressure) applied
to
it.
*
AFTER TOUCH permits controlling
the
depth
of
the
programmed effect
according
to the
pressure applied
to
the keys after initial key attack..
JoD
1
-
BRTH
COllT.
SENSITIVITY
U—
15
Sets
the depth
of
the
effect applied with
the
BREATH CONTROLLER.
*
The data range is
—
15.
At
the
BREATH CONTROLLER
is OFF.
At 15
maximum effect variation
is achieved..
*
The LCD uisplay will
reaci
"FUNCTION 7A
BCS>>BCA>>AFS>>AFA
Breath controlr
sensitivity
(0-15)
;;X".
"XX" is the
aata,
*
If
the
EDIT moue
AilPL.
MODULATION
SENSITIVITY master parameter
is
set
to
for
all
operators, AMPLITUDE
MODULATION
(tremolo, wow) and EG BIAS
(urilliance, expression) will not
function.
Also
if
the
EDIT
laode
PITCH
MODULATION
SENS,
roaster
parameter
is
set to
0,
PITCH MODULATION (vibrato)
will not function.
-*r27
Job
2
-
BRTH CONT, ASSIGN
:
EBC. AMD.
PMD
Selects
the
effect
to
ije
controlled
by
the
BREATH CONTROLLER.
PITCH MODULATION,
AMPLITUDE MODULATION
or
EG
BIAS can
be
selected.
*
The selected function
is
indicated
by
a
3-digit display
(0=iOFF,
1=0N)
.
From
the
left
L.igit
to
the right:
EBC
{EG
B;:AS
CONTROL)
,
AMD (AMPLITUDE
MODULATION
DEPTM)
,
PMD
(PITCIi
MODULATION
DEPTH).
For
example "001"
inaicates that
EBC and
AMD are
OFF,
while PMD
is ON.
*
The
EBC,
AMD and PMD effects are the
same
as
BANK
6
Job
2 -
MOD,
17HEEL
ASSIGN.
^P.3a
*
More
than one effect can
be
selected
at
a
time.
Pressing
the
DATA ENTRY
YES
button consecutively results
in the
following selection sequence:
ooc->ooi->oia->oii->ioo->ici->iic->iii.
Pressing
the
DATA ENTRY NO button
reverses this sequence,
*
The
LCD display
will read "FUNCTION 7A
>>BCSBBBCA>>AFS>>AFA
Breath controller
assign
(EBC, PMD.
AMD) XXX".
"XXX" is
the
effect selection data
as
described
above.
*If
a
BREATH CONTROLLER
is not
connected
and
the
EDIT mode
AMPL.
MODULATION
SENSITIVITY
pararr.eter
is
set to
3
for
all
carriers, the BRTH
CONT.
ASSIGN
EBC
is ON,
and BRTH
CONT.
SENSITIVITY
is
set to 15, no
souno will
be
output.
This
is
because
in the above state, the
BREATH CONTROLLER
is
set up as
a
volume
control, and must
be
blown into
to
produce souna.
Job
3
-
AFTER TOUCH SENSITIVITY
:
—
15
Sets the depth
of
the effect
applied with
AFTER
TOUCH.
*
The data range is 0--15.
At
AFTER
TOUCH is
OFF.
At
15
maximum effect
variation
is
achieveo.
*
The
LCD display
will read "FUNCTION
7A
»BCS»BCA«BAFS>>AFA
After touch
sensitivity
(0-15) XX".
"XX" is the
data.
*
If
the EDIT
mooe
AMPL.
MODULATION
SENSITIVITY
jnaster
parameter
is set to
for
all
operators, AMPLITUDE
MODULATION
(tremolo, wow) and EG BIAS
(brilliance, expression) will not
function.
Also
if
the
EDIT mode PITCH
MODULATION
SENS.
master parameter
is
set to
0,
PITCH MODULATION (vibrato)
v/ill
not function.
Job
4
-
AFTER TOUCH ASSIGN
:
EBC. AMD.
PMD
Selects the effect
to oe
controlled
by
AFTER
TOUCH.
PITCH MODULATION, AMPLITUDE
MODULATION
or EG
BIAS can
be
selected.
*
The selected function
is
indicated
by
a
3-digit display
(0=OFF, 1=0N)
,
Froja
the left digit to the right:
EBC
(EG
BIAS CONTROL)
,
AMD (AMPLITUDE
MODULATION
DEPTH), PMD (PITCH
MODULATION
DEPTH)
*
The
EBC,
AMD and PMD effects
are the
same
as
BANK
6
Job
2
-
MOD.
VJHEEL
ASSIGN.
^P.38
*
More than
one
effect
can be
selected
at
a
time.
Pressing
the
DATA ENTRY
YES
outton consecutively results
in the
following selection sequence:
000->001->01C->011->10 0->101->110->111.
Pressing
the
DATA ENTRY NO button
reverses this sequence.
*
The
LCD display will
read "FUNCTION 7A
>>BCS>>BCA>>AFSBBAFA
After touch assign
(EBC. PMD, AMD)
XXX",
"XXX" is the
effect selection data
as
uescribed
above.
(8)
BANK
8
(F&)
Tills
includes
3
jobs:
the SPLIT
POINT
function used
to
determine
at
v/hich
key the
keyboard will
be
split into channel A and
channel
B
sections, the KEY SHIFT function
which shifts
the range
of
the
keyboard, ana
the
PERFORMANCE NAME function
for
naming
PERFORMANCE MEMORY positions.
39
Advertisement
Table of Contents
