Table of Contents
Advertisement
•
How
to
record
^JLP
Insert
a
formatted
disk into
the
drive.
<*£>
While
holding
PAUSE,
press
REC.
The
song
number
ol
the
song you
are
about
to
record
will
be
displayed.
The
W-50
will
enter the record
ready
mode.
'
If
this
is
the
tirst
-.on;.;
in
lie
recorded
on
the
disk,
it
will
be
song
number
I
.
Il
the disk
already contains
song
data,
the
new
h recorded song
will
be
numbered
alter
the
last
song.
Houcicr,
//
the
ilisk
<
ontains
song
data
that
was
created
on
anothei sequencer, the
song
numbers
mav
be
ditterent,
depending on
the
song names.
^_JC^
Set
the play
tempo
by pressing
TEMPO
•</>.
%^E^
When
you
begin playing the
keyboard, recording
will
start.
You
can
also Mart
ret
ordmg
by
pressing
PLAY
(or
PAUSE).
^
j^
When
you
finish
your performance,
press
STOP
(or
PAUSE).
"
//'
you
pressed
PAUSE,
you
i
an
press
PLAY
(or
PAUSE.) once
again
to
resume
rci
ording
trom
the
pause
point.
'
Never remo\
e the
disk
w
hile
recording
is
in
progress iwhile the
disk
indit.
ator
c bhghtb
lit)!
•
How
to
re-record
(clear
song
data)
<^>
While
holding
REC,
press
CLEAR.
The
display
will
ask
"
Hre
Vou
Sure':-'
".
^jS^
Press
REC
once
again.
The
song you recorded
will
be
cleared
(erased).
Re-record
the
song
using
the
procedure above.
*
This
operation
can be
tised to
clear
not only
the
song you
just
recorded, but
also
other
songs
on
the
disk.
To
clear
another
song,
select
the
song number,
and
perform
the
above
operation.
When
vou
clear
a
song,
the
following
song
numbers
will
be renumbered.
Recording
Song
Data from Another
Device
Into
the
W-50
Song
data
that
was
created
on
a
computer
or
other
sequencer can be recorded
into the
W-50
as
explained
below.
If
you wish
to
play
song
data
that
is
not
in
Standard
MIDI
File
format,
use
this
procedure
to
re-
record
the data
into
the
W-50.
*
MIDI
Clock
(timing
information
for
playback) has
been preprogrammed
to
"INTERNA!"
on
the
W-50,
so
it
will
be unnecessary
to
change
the
settings.
•
Recording
<T>
While
holding
PAUSE,
press
REC.
You
will
enter the record
ready
mode.
C5^
Set
the play
tempo
by
pressing
TEMPO
*</>-.
^3S^
Press
PLAY
(or
PAUSE)
to
begin recording.
^jg^
Start
playback
on your
computer
or other sequencer.
The
data
will
be recorded.
Cls^
When
recording
is
complete,
press
STOP.
* If
you
set
the
W-50
MIDI
Clock parameter
to
"Remote",
the
W-50
will
play/stop
in
response
to
operation of
the
other device
(computer
or
sequencer)
(<*-
P.
74).
* If
the
song
data contains
a
large
number
of
System
Exclusive
messages, they
may
not
be
recorded.
70
Advertisement
Table of Contents
