1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Network Hardware
  5. DS-9608NI-I8
  6. Quick start manual

HIKVISION DS-9608NI-I8 Quick Start Manual

Hide thumbs Also See for DS-9608NI-I8:
Table of Contents

Advertisement

Quick Links

See also: User Manual , Quick Start Manual
Network Video Recorder
Quick Start Guide
UD.6L0202B2166A01

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION DS-9608NI-I8

Summary of Contents for HIKVISION DS-9608NI-I8

  • Page 1 Network Video Recorder Quick Start Guide UD.6L0202B2166A01...

  • Page 2: Table Of Contents

    Network Video Recorder Quick Start Guide TABLE OF CONTENTS Chapter1 Description of Panels ........................6 Front Panel ............................6 Rear Panel ............................. 10 Chapter 2Installation and Connections ......................13 NVR Installation ..........................13 Hard Disk Installation ........................13 Connections ........................... 15 Wiring of Alarm Input ........................
  • Page 3 (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.

  • Page 4: Regulatory Information

    Network Video Recorder Quick Start Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 5: Safety Instruction

    Network Video Recorder Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
  • Page 6 Network Video Recorder Quick Start Guide Applicable Models This manual is applicable to the models listed in the following table. Series Model DS-9608NI-I8 DS-9616NI-I8 DS-9600NI-I8 DS-9632NI-I8 DS-9664NI-I8 DS-7608NI-I2 DS-7600NI-I2 DS-7616NI-I2 DS-7632NI-I2 DS-7608NI-I2/8P DS-7600NI-I2/P DS-7616NI-I2/16P DS-7632NI-I2/16P DS-7708NI-I4 DS-7700NI-I4 DS-7716NI-I4 DS-7732NI-I4 DS-7708NI-I4/8P...

  • Page 7: Chapter1 Description Of Panels

    Network Video Recorder Quick Start Guide Chapter1 Description of Panels 1.1 Front Panel DS-9600NI-I8 Figure 1. 1 Front Panel Table 1. 1 Description of Front Panel Name Function Description ALARM Turns red when a sensor alarm is detected. READY Turns blue when the device is functioning properly. Turns blue when device is controlled by an IR remote.
  • Page 8 Network Video Recorder Quick Start Guide Name Function Description Turns blue when the corresponding channel is recording; turns red when the channel is in network transmission status; turns pink when the channel is recording and transmitting. Universal Serial Bus (USB) ports for additional devices such as USB Interfaces USB mouse and USB Hard Disk Drive (HDD).
  • Page 9 Network Video Recorder Quick Start Guide Name Function Description Buttons In the playback mode, use the Up and Down buttons to speed up and slow down recorded video. Use the Left and Right buttons to select the next and previous video files. Cycles through channels in live view mode.
  • Page 10 Network Video Recorder Quick Start Guide DS-7700NI-I4 (/P) Figure 1. 3 DS-7700NI-I4 Series Table 1. 3 Description of Front Panel Name Function Description POWER Turns green when NVR is powered up. Status Blinks red when HDD is reading/writing. Indicators Tx/Rx Blinks green when network connection is functioning normally.

  • Page 11: Rear Panel

    Network Video Recorder Quick Start Guide 1.2 Rear Panel DS-9600NI-I8 Figure 1. 4 Rear Panel Table 1. 4 Description of Interfaces Item Description LAN1/LAN2 Interface 2 RJ-45 10/100/1000 Mbps self-adaptive Ethernet interfaces provided. LINE IN RCA connector for audio input. AUDIO OUT 2 RCA connectors for audio output.
  • Page 12 Network Video Recorder Quick Start Guide DS-7600NI-I2 and DS-7600NI-I2/P Figure 1. 5 DS-7600NI-I2 Series Figure 1. 6 DS-7600NI-I2/8P Series The DS-7616NI-I2/16P and DS-7632NI-I2/16P provide 16 network Interfaces with PoE function. Table 1. 5 Description of Interfaces Item Description Audio In RCA connector for audio input.
  • Page 13 Network Video Recorder Quick Start Guide DS-7700NI-I4 and DS-7700NI-I4/P Figure 1. 7 DS-7700NI-I4 Series Figure 1. 8 DS-7700NI-I4/16P Series The DS-7708NI-I4/8P provides 8 network Interfaces with PoE function. Table 1. 6 Description of Rear Panel Interfaces Item Description LAN Interface 1 network interface provided for DS-7700NI-I4/P and 2 network interfaces for DS-7700NI-I4.

  • Page 14: Chapter 2Installation And Connections

    Network Video Recorder Quick Start Guide Chapter 2 Installation and Connections 2.1 NVR Installation During installation of the NVR: 1. Use brackets for rack mounting. 2. Ensure ample room for audio and video cables. 3. When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter. 4.
  • Page 15 Network Video Recorder Quick Start Guide Figure 2. 2 Install the HDD 3. Connect one end of the data cable to the NVR motherboard and the other end to the HDD. Figure 2. 3 Connect the data cable 4. Connect the power cable to the HDD. Figure 2.

  • Page 16: Connections

    Network Video Recorder Quick Start Guide 2.3 Connections Wiring of Alarm Input The alarm input is an open/closed relay. To connect the alarm input to the device, use the following diagram. If the alarm input is not an open/close relay, please connect an external relay between the alarm input and the device.

  • Page 17: Using Alarm Connectors

    Network Video Recorder Quick Start Guide Using Alarm Connectors To connect alarm devices to the NVR: 1. Disconnect pluggable block from the ALARM IN /ALARM OUT terminal block. 2. Unfasten stop screws from the pluggable block, insert signal cables into slots and fasten stop screws. Ensure signal cables are tight.

  • Page 18: Hdd Storage Calculation Chart

    Network Video Recorder Quick Start Guide 2.4 HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 128K 160K 192K 224K...

  • Page 19: Chapter 3Menu Operation

    Network Video Recorder Quick Start Guide Chapter 3 Menu Operation 3.1 Menu Structure Refer to the following figure for the menu structure: Menu Playback Maintenance Shutdown Export VCA Search Record Camera Configuration Manual Behavior Normal Normal Schedule Camera General System Info Logout Record General...

  • Page 20: Activating Your Device

    Network Video Recorder Quick Start Guide To shut down the NVR: 1. Enter the Shutdown menu. Menu > Shutdown Figure 3. 2 Shutdown 2. Select the Shutdown button. 3. Click the Yes button. 3.3 Activating Your Device Purpose: For the first-time access, you need to activate the device by setting an admin password. No operation is allowed before activation.

  • Page 21: Login And Logout

    Network Video Recorder Quick Start Guide device starts up. You can click YES and follow the wizard to set a strong password. Figure 3. 4 Warning of Weak Password 3.4 Login and Logout User Login Purpose: If NVR has logged out, you must login the device before operating the menu and other functions. Steps: Select the User Name in the dropdown list.

  • Page 22: User Logout

    Network Video Recorder Quick Start Guide User Logout Purpose: After logging out, the monitor turns to the live view mode and if you want to perform any operations, you need to enter user name and password log in again. Steps: Enter the Shutdown menu.

  • Page 23: Network Settings

    Network Video Recorder Quick Start Guide 3.6 Network Settings Purpose: Network settings must be properly configured before you operate NVR over network. Steps: 1. Enter the Network Settings interface. Menu > Configuration > Network Figure 3. 9 Network Settings Two self-adaptive 10M/100M/1000M network interfaces provided for DS-9600NI-I8 and DS-7700NI-I4, and two working modes are configurable: multi-address and network fault tolerance.

  • Page 24: Live View

    Network Video Recorder Quick Start Guide  OPTION 1: Steps: 1. Click to select an idle window in the live view mode. 2. Click the icon in the center of the window to pop up the Add IP Camera interface. Figure 3.

  • Page 25: One-Touch Raid Configuration

    Network Video Recorder Quick Start Guide 3.9 One-Touch RAID Configuration The RAID is supported by DS-9600NI-I8 series NVR only. Purpose: The device supports the RAID storage function. Through one-touch configuration, you can quickly create the disk array. By default, the array type to be created is RAID 5. Before you start: As the default array type is RAID 5, at least 3 HDDs must be installed in you device.

  • Page 26: Recording Settings

    Network Video Recorder Quick Start Guide 4. When the array configuration is completed, click OK button in the pop-up message box to finish the settings. 3.10 Recording Settings Before you start: Make sure that the disk has already been installed. If not, please install a disk and initialize it. You may refer to the user manual for detailed information.
  • Page 27 Network Video Recorder Quick Start Guide Figure 3. 14 Playback Interface Select the channel (s) you want to play back by checking the checkbox (es), or execute simultaneous playback of multiple channels.

  • Page 28: Chapter 4Accessing By Web Browser

    Network Video Recorder Quick Start Guide Chapter 4 Accessing by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center.
  • Page 29 Network Video Recorder Quick Start Guide Figure 4. 2 Login Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in. After login, you can perform the operation and configuration of the device, including the live view, playback, log search, configuration, etc.
  • Page 30 Network Video Recorder Quick Start Guide...

This manual is also suitable for:

Ds-9616ni-i8Ds-9632ni-i8Ds-9664ni-i8Ds-7608ni-i2Ds-7616ni-i2Ds-7632ni-i2 ... Show all

Table of Contents