Operation; Selecting The Type Of Connection; Sound Settings; Establishing A Bluetooth Connection - Silvercrest SSB 36 A1 Operating Instructions Manual

BB58 B%ERRN 6HLWH  )UHLWDJ  -XQL    

6. Operation

NOTES:
• All adjustments can be conveniently carried out with
the remote control. The basic functions can also be car-
ried out with the buttons on the device. Operation of
the device in the instructions is usually described with
the remote control.
• The device switches to standby mode...
... if no Bluetooth connection is established within
20|minutes or
... if it does not receive a signal for 20 minutes.
• Press the POWER |27 button to switch on the device
from standby mode.

6.1 Selecting the type of connection

1. Press one of the buttons AUX|17, LINE IN|26, OP-
TICAL|16 or |14 to switch to the desired connection
(see "Connections" on page 29).
2. On the audio device you can now start playback and
select and control the music tracks.
NOTE: in order to use the optical input, you need to set
the output of your audio device to "PCM downmix".

6.2 Sound settings

NOTES:
• Changes to the sound settings are acknowledged with
brief flashing of the LED|1, until the minimum/maxi-
mum value has been reached.
• Controlling the levels of the treble and bass is exclu-
sively possible in the "Music" settings, after pressing
the MUSIC|18, button.

Controlling the volume

• During playback, press the VOLUME –/+|19 buttons.
Muting the device
1. Press MUTE|15 to switch off the sound. The LED|1
flashes.
2. To switch the sound back on, press MUTE again or
one of the VOLUME –/+|19 buttons. The LED|1
lights up.
Adjusting the tone quality
• Press one of the buttons|18, to select the pre-sets for
the tone quality for music (MUSIC), films (MOVIE) or
language (DIALOG).
• Press the MUSIC|18: button
- Use the TREBLE –/+|25 buttons to adjust the treble
sounds.
- Use the BASS –/+|21 buttons to adjust the bass
sounds.
30 GB
6.3 Establishing a Bluetooth
connection
NOTES:
• The identification of the device is "SSB|36|A1".
• After it has been switched over to Bluetooth, the device
automatically attempts to establish a connection with
the last paired device.
• Please observe that the establishment process of the
connection may vary slightly depending on the device
and the software used.
1. Press the |14 button to switch over to a Bluetooth
connection. LED|1 flashes blue.
2. Switch on the audio device (e.g. smartphone) and start
the Bluetooth connection.
3. Press the PAIR|5 button on the device for approxi-
mately 1 second. The blue LED|1 flashes rapidly. The
audio device will now receive the device identification
"SSB|36|A1".
4. Establish the connection with the soundbar on the au-
dio device. If you are asked for a password, enter
"0000". Both devices are now interconnected. LED|1
now lights up in blue and a beep is heard.
NOTE: it is possible that audio devices remember the iden-
tification of the device. In this case, it may not be neces-
sary to establish the connection manually again if the
Bluetooth function is activated.
5. Now play a song on the audio device. The sound is
played back from the soundbar.
6. With the I WW |24, XX I |20 and
can select and control the music tracks.

7. Cleaning and storing

DANGER! Risk of electric shock!
~ Pull the power unit|7 out of the wall socket before you
clean the device. Make sure that no liquid gets into the
device.
• Clean the device with a slightly damp cloth. Solvents,
spirits, thinners etc. must not be used, as they can
damage the surface of the device.
• When not using the device, store it in a place where
neither high temperatures nor moisture can affect it.
Remove the battery from the remote control.
X / II |23 buttons you