Part 3 Key Split Mode - Casio CZ-1 Operation Manual

KEY
SPUT MODE
^IKEYfiSPLniSETinNGS
With the CZ-1,
two tones can be assigned
to
the
upper
and
lower ranges
of
the keyboard.
The
split
point
of
the
keyboard and
the individual
volumes
of
the
two tones can be
freely set,
and
effects
can
be
set
to
ON
and OFF.
(1)
SPLIT
POINT SETTING
Press the
KEY
SPLIT
key
in
the
Mode
Select Section.
SPLIT
POINT =
24
SP
24
LOUER
LEU=15
UPPER
LEU=15
n
LOWER
tone
level
(1-15)
Cursor
UPPER
tone
level
(1-15)
Use
the
CURSOR
keys
to
move
the cursor
to
the
SPLIT
POINT
value.
Use
the
VALUE
keys
to
set
the value
within
a range
of
1
through
60.
This determines the
split
point.
1
10
20 30 40 50
60
iiiiiiiiiiliiiiiiiiiii
iiidii
SPLIT
POINT
= 24
(2)
TONE AND VOLUME
LEVEL
®
Use
the
B
CURSOR
key
to
move
the cursor
to
the
LOWER
LEVEL
value.
Here, the
LOWER
tone
and
volume
level
are
set.
•Select
one
of
the
internal
or cartridge
tones using
the
Programmer
Section.
The
tone selected
will
be
play-
able
to
the
left
of the
split
point.
•The
VALUE
keys
in
the
Data Entry Section are
used
to
set the
volume
level within
a range
of
1
through
1
5.
A
setting of
15 represents
maximum
volume.
®
Use
the
S
CURSOR
key
to
move
the cursor
to
the
UPPER
LEVEL
value. Select the tone
and
set
the
volume
In
the
same way
as
for
the
LOWER
LEVEL.
Now
the
keyboard
is
split for
simultaneous, separate
play of
two
tones.
(3)
SUSTAIN
PEDAL
ENA/DIS
The
sustain pedal
effect
can be
applied independently
to
the
UPPER
and
LOWER
tones used
in
the
KEY
SPLIT mode.
The
display
will
appear as
illustrated
in
Fig.
1
when
the
PAGE UP
key
is
pressed
while
in
the
KEY
SPLIT mode.
(Fig. 1)
SUS.PEDRL
LCH...i=EN a
UPF-EHfl
'
—
Cursor
'
ENA/DIS
'
—
ENA/DIS
"ENA"
is
the abbreviation
of
the
word
"enable" which
indicates that
the
pedal
effect
is
applied, while ''DIS"
or
"disable"
means
that the effect
is
not applied.
®When
the cursor
is
located
under
the
LOWER
specification
as
shown
in
Fig.
1,
the
VALUE
00
keys
can be used
to
switch
between
sustain
pedal
ENA/DIS
for
the
LOWER
tone.
(5)
Moving
the cursor
to
the
UPPER
specification
makes
it
possible
to
use the
VALUE
SB
keys
to
switch
between
sustain
pedal
ENA/DIS
for
the
UPPER
tone.
*Note
that
UPPER
and
LOWER
cannot
both
be
set to
DIS
at
the
same
time.
"Setting
LOW
=
DIS/UPPER =
ENA
causes
the
upper
tone to
be
held
when
the sustain pedal
is
depressed.
-43-