Effect/Overall Control - Casio CZ-1 Operation Manual

'coNfTrKmmmi
S^he
KEY
?m
ifmn?
^^"^
'"
*''^*^'"' ''"°''
'^"
'^^
"^*
'"
^^^
"^^Y SPLIT mode. The
EFFECT SECTION
data
?
M^n^
.?^t3.r^®
'^ ''°"''"°" ""^^ *^^* °' *^^
NORMAL
mode,
but the
PORTAMENTO
ON/OFF
GLIDE
ON/0?P
and MODULATION ON/OFF
key
status
can
be
set independently
in
each mode.
Setting of the
rbLOON/SFFkeJ
rn^r NORMAL
m'od'e'''
^"'
''"
™'''°'^
^^«'"^^
^'^ ^'^^ ^^-''^'^
^'^^ *^^
--
p'-^-
asTat'uie^^
:
EFFECT.
PORTAMENTO
GLIDE
PITCH
BEND
MOD. WHEEL
/AFTER
TOUCH
..Parameters (EFFECT SECT
ION)
SWEEP
=
0.1/TIME
=
00- -99
NOTE=
-12~+12/TIME =
00~99
RANGE=0-12
MOD. WHEEL
DEPTH
=
00
-^99
MOD. AFTER TOUCH
DEPTH
= 00
-99
AMP. AFTER TOUCH RANGE
=
00~15
CONTROL
ON/OFF
ON/OFF
BEND WHEEL
MOD. WHEEL
Key
after
touch
Key
after touch
^PORTAMENTO
ON/OFF,
GLIDE
ON/OFF, and
SOLO
ON/OFF
can be
set
independently
for the
UPPER
and
LOWER
tones.
PITCH
BEND
and MODULATION
are
applied
commonly
to
both the
UPPER
and
LOWER
tones.
The
latest panel
settings
made
In
the
KEY
SPLfrl
modeam
retained
when
another
mode
is
entered
fe
or
the
power
of
trie
unit
is
switched OFE^See
e^
tPART54
OPERATION
MEMORY5tor)tieteil^:6ni^
saving
multiple settings
in
memory
and
retaining^
important
key
split settings;.
:
.,
./
i
sSRllnsMODEiSOUNDIGREAnOM
seo^^rcTMtTJm^^^ '«'
"^"^
°' *^*'
'"°.
?"'!
"'^^
'°^
'^^^
^^^'^
'^^'^
^^
^^'
°
°^«^te
"ew
sounds.
Two
separate COMPARE/RECALL
areas
are retained
for
the
UPPER
and
LOWER
tones,
and
all
tone data
settinas
are
performed
using the same
procedure as
that outlined
for
the
NORMAL
mode.
^
(1)
SOUND
CREATION
®
Switch
the
KEY
SPLIT
key
ON
to
enter the
KEY
SPLIT mode.
SP LOUER
IIPPEP
30 LEU=15
LEi.i=l.S
"
C
-Cursor
©Use
the
CURSOR
HB
keys
to
move
the cursor
under
the value
of the tone
to
be
created.
(D
Use
the
PARAMETER
section
to
create the desired
sound.
At
this time, the
indicator above
the
COM-
PARE/RECALL
key
in
the
PROGRAMMER
SEC-
TION
will light to indicate that
the
changed
data
is
stored
for
the tone under which
the cursor
is
located.
~/P~
Lights
®
The
CURSOR
H B
keys
can be used
to
move
the
cursor under
the value
of
the other
tone.
The above
procedures
are then
repeated and
both tones are
stored
In
separate COMPARE/RECALL
areas.
(2)
TONE
DATA WRITE
Tones
created
in
the
KEY
SPLIT mode
can be
stored
in
the
internal
bank
or cartridge with the
same
proce-
dures as those used
in
the
NORMAL
mode
(see
p
36).
Simply use
the
CURSOR
B
B
keys
to
move
the
cur-
sor under
the desired tone
and
use
the
WRITE
key
to
write the data
to the
internal
bank
or cartridge.
NOTE
The
procedures
for
TONE DATA
SAVE/LOAD
and
EXCHANGE
in
the
NORMAL
mode
are iden-
tical for
the
KEY
SPLIT mode.
-45-