Casio CZ-1 Operation Manual page 48

!
<TONE
MIX
MODE
OPERATION
>
The
called operation
is
specified for
the
TONE
MIX
mode when
the
indicators
above, both the
TONE
MIX
key and
OPERATION
MEMORY
key
in
the
MODE
SELECT
SECTION,
are
lit
as
illustrated
in
Fig. 3.
At
this
time,
the
LCD
will
show
the
two tones used
in
the
tone
mix.
The example
in
Fig.
4
shows
internal A-1
(T0NE1) and
internal
A-6
(T0NE2),
with the tone
name
displayed
(BRASS
1)
being
that for
the current cursor
location
(TONE1).
*Each
press
of
the
CURSOR
H B
keys
in
the
DATA
ENTRY SECTION
switches
between
the
two tones
and
also
switches
the
name
at
the
bottom
of the
LCD.
(Fig- 3)
-TONE
MIX
OPERATION
-
N
1
^
-
—
cm
—
^\
TONE
MX
1
KEY
SPLIT 1
^^ISSS^j
(2)
OPERATION
MEMORY
CALL
64
operations are preset
in
the
OPERATION MEMORY.
Selection
is
performed using
the
MEMORY
BANK
(A^H)
and
MEMORY
NO.
(1^8) keys
in
the
PROGRAMMER
SECTION.
MEMORY
BANK
keys
MEMORY
NO. keys
Operation
number
indicators
light
(Fig. 4)
-OPERATION
MEMORY
display
-Internal
tone
A-1
Internal tone A-6
•—Cursor
Name
of
tone
where
cursor
is
located
<KEY
SPLIT
MODE
OPERATION >
The
called operation
is
specified
for
the
KEY
SPLIT
mode when
the indicators above, both the
KEY
SPLIT
key and
OPERATION
MEMORY
key
in
the
MODE
SELECT
SECTION,
are
lit
as
illustrated
in
Fig. 5.
At
this
time, the
LCD
will
show
the
two tones used
in
the
key
split.
The
example
in Fig.
6
shows
internal
H-3
(LOWER)
and
cartridge
F-6
(UPPER),
with the
tone
name
displayed
(CONGA)
being
that for
the current
cur-
sor location
(LOWER).
*Each
press
of the
CURSOR
H
keys
in
the
DATA
ENTRY
SECTION
switches between
the
two
tones
and
also
switches
the
name
at
the bottom
of the
LCD.
(Fig- 5)
pKEY
SPLIT
OPERATION
NOflMAL
I
TONC
MX
I KCV S»LIt|
(Fig. 6)
pOPERATION
MEMORY
display
-Internal
tone H-3
-Cartridge tone F-6
-Cursor
Name
of
tone
where
cursor
is
located
•The
contents
of the selected operation are
shown
on
the
LCD
(see
preceding
Figs.1
-6).
•The
OPERATION
MEMORY
mode
is
entered
when
power
is
switched on
if
it
was
selected
when
power
was
switched
OFF, and
the
last
operation selected
is
called.
•The
indicators
in
the
PROGRAMMER
SECTION
show
the operation
number
in
the
OPERATION MEMORY
mode, and
tone
numbers
are
shown
on
the LCD.
(3)
CARTRIDGE OPERATIONS
Besides the operations used by
the
internal
tones, oper-
ations
used by
cartridge tones
can
also
be
stored
in
the operation
memory.
OF'EM I.fl-1
C.B-l
BRRSS
1
JF-EM
C.E-S C.H-1
UOICE
3
OPEM
C.G-8
SVNTH.LEflD
5
-
Combination
of
internal tone
and
cartridge tone
-Two
cartridge
tones
NORMAL
mode
-47-