Casio CZ-1 Operation Manual page 26

This
pitch
maintained
/while key
is
pressed.
L2-SUSTAIN
POINT
KEY
OFF END
POINT
Jimi
SmEP^2 STEP,3
^.STEF.4
^:pATf^^.
99 72
60 20
W^M
99 66 24 00
%^JEmi
***
BUS
***
END
-Time
®
When
the
ENV
key
of
the
DCO
1
or
DCO
2
is
pressed, the following
appears on
the
LCD.
®
Use
the
PAGE UP
key
to
advance
to
STEP
2.
After
ensuring
the
STEP
2
is
displayed, follow the
same
procedures
outlined for
STEP
1
to
set the
RATE
to
72
and
the
LEVEL
to 66.
PITCH STEP2
=+=++•
RflTE=72
LEUEL=66
(D
Press
the
ENV POINT SUSTAIN
key
to
designate
STEP
2 as a
SUSTAIN POINT.
SUSTAIN POINT
PITCH STEP2 SUS
RflTE=72 LEUEL=6!S
(6)
Use
the
PAGE UP
key
to
advance
to
STEP
3
and
set
the
RATE
to
60 and
the
LEVEL
to
24.
PITCH STEP3
+++
RRTE=60
LEi...iEL=24
SUS
will
be displayed
if
the displayed
STEP
is
a
sustain point.
END
will
be
displayed
if it
is
an
end
point.
Pitch
envelope
STEP
1
selected.
4-
PITCH STEPl
++=
Rf\JE=rn,m. LEUEL=«'«^'
/ 00^/^1/772^99 \
KoO^ninz
^99
/
Destination level of
step
1.
Rate
of
step
1
®
Use
the
VALUE
key
to
raise
the
RATE
value to
99.
PITCH STEPl
+++
RflTE=92
lBJEL^n,n.
®
Use
either
one
of
the
CURSOR
keys
to
nnove the
cursor
under
the
LEVEL
value.
Use
the
H
VALUE
key
to
raise
the
LEVEL
value
to
99.
This connpietes
the setting of
STEP
1.
PITCH STEPl
+++
RHTE=99 LEUEL=92
(7)
Use
the
PAGE UP
key
to
advance
to
STEP
4 and
set
the
RATE
to
20.
Then
press
the
ENV
POINT
END
key
to set
the
END
POINT, and
the
LEVEL
will
automatically
be
set to 00.
*lt is
not
necessary
to
press the
END
key
if
the
END
POINT
is
already
set.
END
POINT
PITCH STEP4 END
RflTE=20
LEUEL=00
LEVEL
of
the
last
step
is
00.
•Even
if
the
PAGE UP
key
is
pressed,
it
will
be
Impossible to
advance from the present step
if
END
POINT
is
specified. In this
case, press the
ENV
POINT
END
key again
to
cancel
the
END
point
and
then press the
PAGE UP
key.
If
an
END
point
is
cancelled within
STEP
1
through
7,
an
END
POINT
is
automatically designated
in
STEP
8
and
previously set
data
is
automati-
cally
restored.
•The
LEVEL
for
a
STEP
that
includes
an
END
POINT
is
fixed
as
GO and cannot be changed.
•When
a
SUSTAIN POINT
is
designated
in
a
STEP,
SUSTAIN POINTS
which are
set
in
other
STEPS
are cancelled.
-25-