Casio CZ-1 Operation Manual page 11

(DLEVEL
key
Pressed
to set the
overall
volume
level for
the LINE
1
DCA.
©VELOCITY
key
Pressed
to set
the degree
of
change
in
accordance
with
the
key touch
strength
for
the
LINE
1
amp
(volume),
wave
(timbre),
and
pitch
(pitch)
envelopes.
©WAVEFORM
key
Pressed
to select the
LINE 2 waveform.
®DCO
ENV
key
Pressed
to
set the
LINE
2
pitch envelope.
®DCW
KEY FOLLOW
key
Pressed
to
cause
the waveform
for
the
LINE
2
DCW
to
approach a
sine
wave
(cosine
wave)
at
the higher
range
of
the keyboard.
®DCW
ENV
key
Pressed
to set the
LINE
2
wave
envelope.
@)DCA KEY
FOLLOW
key
Pressed
to
cause
the envelope
for
the
LINE
2
DCW
to
shorten (timewise)
at
the higher
range
of
the keyboard.
©DCA
ENV
key
Pressed
to
set the
LINE
2
amp
envelope.
©LEVEL
key
Pressed
to set
the
overall
volume
level for the
LINE 2
DCA.
©VELOCITY
key
Pressed
to
set the
degree
of
change
in
accordance
with
the
key touch
strength
for
the
LINE
2
amp
(volume),
wave
(timbre)
and
pitch
(pitch)
envelopes.
©VIBRATO
key
Pressed
to set vibrato
for
each
tone
in
accordance
with
four parameters: wave,
delay,
rate, depth.
©OCTAVE
key
Pressed
to raise or lower the
pitch of
a tone
in
one-
octave
steps.
(D
DETUNE
key
Pressed
to set differences
in
pitch
between LINE
1
and
LINE
1', or
LINE 2 and LINE
2'.
©LINE SELECT
key
Pressed
to select
a
line
or
line
combination
for
sound
creation.
Each
press
of this
key changes
the
line
set-
ting
in
the
sequence: [l]-^[2]-*|Tl
+
[2l-^[i]-f
\r\
,
and a
indicator
lights to
show
the current
selection.
©RING
key
Pressed
to
apply
ring
modulation
to either
LINE 1'
or
LINE 2\
©NOISE
key
Pressed
to
apply noise modulation
to either
LINE
1
'
or
LINE 2\
\
(w)NAME
key
Pressed
to
allow
writing of
a
name
up
to
1
6
characters
long
for
a
tone.
©PARAMETER COPY
key
Used
to
copy waveform and envelope parameter
data
between LINE
1
and LINE
2
in
single-parameter
units.
©INITIALIZE
key
Pressed
to initialize
each
data
value. This key
is
held
down
and
the
parameter key
for the value
to
be
initial-
ized
is
pressed
simultaneously.
®
MODULATION WHEEL
Turning
this
wheel when
the
MODULATION
ON/OFF
key
in
the
OVERALL CONTROL
SECTION
is
ON
adjusts
vibrato depth
in
accordance
with the range
set using the
MODULATION WHEEL/AFTER
TOUCH
key
in
the
EFFECT
SECTION ®.
•Turning the wheel has no
effect at
all
when
the
MODUALTION ON/OFF
key
is
OFF.
@
PITCH
BEND WHEEL
Turning
this
wheel
controls
pitch
in
accordance
with the
range
set
using the
BEND RANGE
key
in
the
EFFECT
SECTION
d).
@
Keyboard
A
61
-key, 5-octave. 16-note
maximum
polyphonic keyboard
with
initial/after
touch sensors.
'8-note polyphonic
when
2DC0
is
being used,
4-note polyphonic
when
TONE
MIX
is
being used,
monophonic
when
SOLO
is
ON.
-10