Part 2 Tone Mix Mode; Tone Mix Settings - Casio CZ-1 Operation Manual

PART
2
TONE MIX MODE
^2-lfilBNEii
With
the CZ-1, two
of the 128
cartridge
and
internal
tones can be mixed
for output.
The
volumes
of
the
individual
tones
that
make
up a
tone mix can be
independently
controlled. At
this time, the
keyboard becomes
4-note polyphonic.
(1)
TONE AND VOLUME
LEVEL
®
Press
the
TONE
MIX
key.
—
cu
—
H
TONE MIX
LEUi=15 LEU2=15
t
LQursor
t
Volume
level of
TONE
1
(1-15)
Volume
level of
TONE
2
(1-15)
®
Tones
can be
selected and
the
volume
can be
set
for the
position
(LEV 1/LEV
2) at
which
the cursor
is
located.
In
the
situation
shown
above,
the cursor
is
below
the
level for
TONE
1
,
and so
the tone
and
volume
level
can be changed.
•Select
1
tone from the
internal
bank
or
cartridge.
•Use
the
VALUE
keys
to set the
volume
level within
a range
of
1
through
15.
A
setting of
15 represents
maximum
volume.
(2)
Use
the
CURSOR
key
in
the Data
Entry Section
to
move
the cursor under
the
LEV
2
value. Set the
tone
and volume
level
in
the
same manner
as
that
outlined
for
LEV
1.
(2)
TONE
2
PITCH
SETTING
Changing
the
TONE
2
pitch within the
range
of
±
4
oc-
taves
makes
it
possible
to offset the pitches
of
TONE
1
and
TONE
2
to
produce sounds
that
are
deeper and
mellower.
The method
used
to specify the data
in this
procedure
is
identical to that
used
for
PARAMETER
SECTION DETUNE.
-40-
The
display
will
appear as
illustrated
in Fig.
1
when
the
PAGE UP
key
is
pressed
while
in
the
TONE
MIX
mode.
(Fig. 1)
Determines whether
the
pitch
will
be
offset
upwards
(+)
or
downwards
(-).
T0NE2
(+)
i:ii::T=0
NCiTE=e
FIHE=00
Pitch
offset
in
octave
units
(0*3)
Cursor
Pitch offset
in
1/60 semitones (0-60)
Pitch
offset
in
semitone
(100<c
units (0-11))
0+/-
Use
the
CURSOR
H
key
to
move
the cursor below
the
"
+
"
(or
"
-
")
display. Pressing the
VALUE
HH
keys
changes
the display
to "
+
"
(for
upwards
offset)
or
*'
- "
(for
downwards
offset).
(DOCT
Use
the
CURSOR
[] key
to
move
the cursor below
the
OCT
value.
Pressing the
VALUE
keys
changes
the value
in
the
range
of
0-3.
(3)
NOTE
Use
the
CURSOR
H
key
to
move
the cursor below
the
NOTE
value.
Pressing the
VALUE
00
keys
changes
the value
in
the
range
of
00-11.
0FINE
Use
the
CURSOR
key
to
move
the cursor
below
the
FINE
value.
Pressing
the
VALUE
keys
changes
the
value
in
the
range
of
00-60.
*The
data included
in
®-®
above makes
it
possible
to set pitch within
a range
of
±4
octaves.
The
pitches
of
TONE
1
and
TONE
2 are
identical
when
OCT,
NOTE
and FINE
are
all
set to
0.