Jasic MIG SERIES Operator's Manual
Compact welding machines
Hide thumbs
Also See for MIG SERIES:
- Operator's manual (48 pages) ,
- Operator's manual (19 pages) ,
- Operator's manual (48 pages)
Related Manuals for Jasic MIG SERIES
Summary of Contents for Jasic MIG SERIES
- Page 1 MIG Series MIG/MAG/MMA Compact welding machines Order code ! JM-200CS OPERATOR MANUAL...
- Page 2 Your new product Thank you for selecting this Jasic Technology, Wilkinson Star product. This product manual has been designed to ensure that you get the most from your new product. Please ensure that you are fully conversant with the information provided paying particular attention to the safety precautions. The information will help protect yourself and others against the potential hazards that you may come across.
-
Page 3: Safety Precautions
Safety Precautions These general safety norms cover both arc welding Insulate yourself from work and ground using dry insulating mats or covers big enough to prevent any physical contact machines and plasma cutting machines unless with the work ground. otherwise noted. Never touch the electrode if you are in contact with the work The equipment must only be used for the purpose it was ground, or another electrode from a different machine. - Page 4 Do not weld on coated metals, unless the coating is Replace the coverings and protections and close all doors removed from the weld area, the area is well ventilated, and when the intervention is finished, and before starting the while wearing an air-supplied respirator. The coatings on equipment.
- Page 5 Keep your head and face away from the cylinder valve outlet RF Declaration when opening the cylinder valve. Equipment that complies with directive 2004/108/EC Always secure the cylinder safely concerning electromagnetic compatibility (EMC) and the technical requirements of EN60974-10 is designed for use in Never deface or alter any cylinder industrial buildings and not those for domestic use where electricity is provided via the low voltage public distribution...
-
Page 6: Product Overview
Product Overview The unique electronic structure and air channel design in Reduction in magnetic and resistance loss enhances the • welding efficiency and energy saving effect. this series of machines provides efficient cooling of the power devices as well as improving the duty cycles of the Working frequency is beyond the audio range, which •... -
Page 7: Technical Data
Technical data Parameter Unit MIG 200CS Rated input voltage 230V AC +/- 15% Rated input power 9.4 MMA Recommended fuse MMA 10 - 200 MIG 30 - 200 Welding current range Welding current range MMA 20.4 -28 MIG 15.5 - 24 Rated duty cycle 200A @ 35% No load voltage... - Page 8 Controls Front view Current/wire feed speed control knob Current display window 2T indicator 4T indicator 2T/4T switch key Welding mode selecting switch Gas/no gas switch Socket for spool gun torch (optional) "+" output terminal Euro connector for torch "-" output terminal VRD ON VRD OFF Voltage/arc force/downslope time control knob...
- Page 9 Optional spool gun socket Socket 1: Push-pull torch power source ”+” Socket 2: Push-pull torch power source ”-” Socket 3~9: Null Rear view Input power cord Gas inlet Power switch Side view Handle Wire-inch button Gas-check button Wire feed system...
-
Page 10: Installation
Installation Unpacking Check the packaging for any signs of damage. Carefully remove the machine and retain the packaging until the installation is complete. Location The machine should be located in a suitable position and environment. Care should be taken to avoid moisture, dust, steam, oil or corrosive gases Place on a secure level surface and ensure that there is adequate clearance around the machine to ensure natural... - Page 11 selector into the “+” output terminal of the welding machine, Connect the cylinder to the gas inlet on the back and tighten it clockwise. panel of the machine, adjust the gas flow to the appropriate value, and open the gas valve. Please note that the joint Ensuring that the groove size in the feeding position on the should be tightened to prevent gas leakage.
- Page 12 Operation Before starting any welding activity ensure that you have Gas less MIG suitable eye protection and protective clothing. Also take the necessary steps to protect any persons within the The operation method is the same to MIG operation except area.
- Page 13 After the parameter adjustment is done, press the 2T/ Multifunctional display window 4T switch key again to store the system parameters. Then, the machine enters into standby mode. During welding, the current display window displays the practical welding current value, and the voltage display window displays the practical welding voltage value.
-
Page 14: Maintenance And Troubleshooting
Maintenance and troubleshooting The following operation requires sufficient professional Troubleshooting knowledge on electric aspects and comprehensive Before arc welding machines are dispatched from the safety knowledge. Make sure the input cable of the factory, they have already been checked thoroughly. The machine is disconnected from the electricity supply and machine should not be tampered with or altered. -
Page 15: Electrical Schematic
Electrical schematic... -
Page 16: Parts List
Parts list... - Page 17 No. Part no Description Part no Description 1 10045881 Inverter 15 10041421 Wire feed system 2 10041446 Fan 16 10045805 Display panel mounting 3 10037485 Rectifier board 17 10043904 Knob 4 10041723 Gas Connector 18 10037151 Quick Socket 5 10041721 Silicon bridge heat sink 19 10041427 Handle Line 6 10046146 Machine Cover 20 10041419 Torch connector body...
- Page 18 JM MIG Series MIG/MAG/MMA WELDING MACHINE Order code ! JM-200CS (MIG 200CS) © Wilkinson Star Limited Issue 1 May 2014 Product is subject to change without notice xvii...