Specifications - Onkyo TX-DS696 Instruction Manual

Specifications

AMPLIFIER SECTION
Continuous Average Power output (FTC)
All channels:
Continuous Power output (DIN)
Maximum Power output (EIAJ)
Dynamic Power Output (Stereo)
Total Harmonic Distortion:
IM Distortion:
Damping Factor:
Input Sensitivity and Impedance
PHONO:
LINE (CD, TAPE, DVD,
VIDEO 1-4):
MULTICHANNEL INPUT
(FRONT L/C/R, SURROUND L/R):
(SUBWOOFER):
COAXIAL 1, 2 (DIGITAL):
DVD, VIDEO1-4:
COMPONENT VIDEO 1, 2:
Output Level and Impedance
Rec out (TAPE, VIDEO 1, 2): 200 mV, 2.2 kΩ
Pre out:
VIDEO (VIDEO 1, 2, MONITOR OUT):
COMPONENT VIDEO OUT: 1 Vp-p, 75 Ω (Y)
Phono Overload:
Frequency Response:
RIAA Deviation:
Tone Control
Bass:
Treble:
Signal-to-Noise Ratio (Stereo)
Phono:
CD/Tape:
Muting:
100 W per channel min. RMS at 8
Ω, 2 channels driven from 20 Hz
to 20 kHz with no more than
0.08% total harmonic distortion.
125 W min. RMS at 6 Ω, 2
channels driven from 1 kHz with
no more than 0.1% total
harmonic distortion.
130 W at 6 Ω
160 W at 6 Ω
2 × 230 W at 3 Ω
2 × 170 W at 4 Ω
2 × 115 W at 8 Ω
0.08% at rated power
0.08% at 1 W output
0.08% at rated power
0.08% at 1 W output
60 at 8 Ω
2.5 mV, 50 kΩ
200 mV, 50 kΩ
200 mV, 50 kΩ
36 mV, 50 kΩ
0.5 Vp-p, 75 Ω
1 Vp-p, 75 Ω
1 Vp-p, 75 Ω (Y)
0.28 Vp-p, 75 Ω (C)
1 Vp-p, 75 Ω (Y)
0.7 Vp-p, 75 Ω (C
/C P /P )
B R, B R
1 V, 470 Ω
1 Vp-p, 75 Ω
1 Vp-p, 75 Ω (Y)
0.28 Vp-p, 75 Ω (C)
0.7 Vp-p, 75 Ω (C
/C P /P )
B R, B R
110 mV RMS at 1 kHz, 0.5% T.H.D.
5 Hz to 100 kHz: +1 dB, –3 dB
20 Hz to 20 kHz : ±0.8 dB
±10 dB at 50 Hz
±10 dB at 20 kHz
80 dB (IHF A, 5 mV input)
100 dB (IHF A, 0.5 V input)
–50 dB
TUNER SECTION
FM
Tuning Range:
Usable Sensitivity
Mono:
Stereo:
50 dB Quieting Sensitivity
Mono:
Stereo:
Capture Ratio:
Image Rejection Ratio:
USA & Canadian models:
Other area models:
IF Rejection Ratio:
Signal-to-Noise Ratio
Mono:
Stereo:
Alternate Channel Attenuation:
Selectivity:
AM Suppression Ratio:
Total Harmonic Distortion
Mono:
Stereo:
Frequency Response:
Stereo Separation:
AM
Tuning Range
USA & Canadian models:
European & Australian models:
Worldwide models:
Usable Sensitivity:
Image Rejection Ratio:
IF Rejection Ratio:
Signal-to-Noise Ratio:
Total Harmonic Distortion:
GENERAL
Power Supply:
Power Consumption:
Dimensions (W × H × D):
Weight:
REMOTE CONTROLLER
Transmitter:
Signal range:
Power supply:
Specifications and features are subject to change without notice.
Power supply and voltage vary depending on the area in which the
unit is purchased.
87.5 to 108.0 MHz (50-kHz steps)
11.2 dBf, 1.0 µV (75 Ω IHF)
0.9 µV (75 Ω DIN)
17.2 dBf, 2.0 µV (75 Ω IHF)
23 µV (75 Ω DIN)
17.2 dBf, 2.0 µV (75 Ω)
37.2 dBf, 20 µV (75 Ω)
2.0 dB
40 dB
85 dB
90 dB
76 dB
70 dB
55 dB
50 dB (DIN)
50 dB
0.2%
0.3%
30 Hz to 15 kHz, ±1.0 dB
45 dB at 1 kHz
30 dB at 100 Hz to 10 kHz
530 to 1,710 kHz (10-kHz steps)
522 to 1,611 kHz (9-kHz steps)
531 to 1,602 kHz (9-kHz steps)
530 to 1,710 kHz (10-kHz steps)
30 µV
40 dB
40 dB
40 dB
0.7%
AC 120 V, 60 Hz
(USA & Canadian models)
AC 230-240 V, 50 Hz
(European & Australian models)
AC 220-230 and 120 V switchable,
50/60 Hz (Worldwide models)
5.7 A
460 W
435 × 175 × 431 mm
17-1/8" × 6-7/8" × 16-15/16"
27.8 lbs. (USA & Canadian models)
13.5 kg (Other models)
Infrared
Approx. 5 meters, 16 ft.
Two "AA" batteries (1.5 V × 2)
61