Video Input Setup - Onkyo TX-NR1007 Instruction Manual

First Time Setup—Continued

Video Input Setup

HDMI Input Setup
If you connect a video component to HDMI IN, you
must assign that input to an input selector. For example,
if you connect your DVD/BD player to HDMI IN 1, you
must assign HDMI IN 1 to the DVD/BD input selector.
If you've connected your TV to the AV receiver with an
HDMI cable, you can set the AV receiver so that
composite video, S-Video, and component video sources
are upconverted* and output by the HDMI output. You
can set this for each input selector by selecting the
"- - - - -" option.
Composite video, S-Video,
component video
IN
OUT
Composite video, S-Video,
component video
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn't appear, make
sure the appropriate external input is
selected on your TV.
2 Use the Up and Down [q]/[w] but-
tons to select "1. Input/Output
Assign", and then press
[ENTER].
The "Input/Output Assign" menu
appears.
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
3 Use the Up and Down [q]/[w] but-
tons to select "2. HDMI Input",
and then press [ENTER].
The "HDMI Input" menu appears.
1–2. HDMI Input
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
4
HDMI
HDMI
5
Notes:
• For composite video, S-Video, and component video
upconversion for the HDMI output, the "Monitor Out"
setting must be set to other than "Analog" (see
page 47), and the "HDMI Input" setting must be set to
"- - - - -". See page 27 for more information on video
signal flow and upconversion.
• If no video component is connected to HDMI output
(even if the HDMI input is assigned), the AV receiver
selects the video source based on the setting of
Component Video Input.
• When an HDMI IN is assigned to an input selector, the
AV receiver will select audio from HDMI IN as a pri-
ority. See "Digital Audio Input Setup" on page 51.
• The TUNER input selector cannot be assigned and is
fixed at the "- - - - -" option.
• If you connect an input component (such as UP-A1
Dock that seated iPod) to the UNIVERSAL PORT
jack, you cannot assign any input to PORT selector.
• Do not assign the component connected with the
HDMI input to the TV/TAPE selector when you set
"TV Control" setting to "On" (see page 109).
Otherwise, appropriate CEC (Consumer Electronics
Control) operation is not guaranteed.
HDMI1
• This procedure can also be performed on the AV
HDMI2
HDMI3
receiver by using its [SETUP] button, arrow buttons,
HDMI4
and [ENTER] button.
HDMI5
Use the Up and Down [q]/[w] but-
tons to select an input selector,
and use the Left and Right [e]/
[r] buttons to select:
HDMI1, HDMI2, HDMI3, HDMI4,
HDMI5, HDMI6:
Select the HDMI IN to which
the video component has
been connected.
- - - - -: Output composite video,
S-Video, and component
video sources from the HDMI
outputs. The video output sig-
nal from the HDMI outputs is
the one configured in "Com-
ponent Video Input Setup"
(see page 50).
• Each HDMI IN cannot be assigned to
more than one input selector. When
HDMI IN have already been
assigned, you must set first any
unused input selectors to "- - - - -" or
you will be unable to assign HDMI
IN to input selector.
Press the [SETUP] button.
The setup menu closes.
49