Rotel A14 Owner's Manual page 16

16
• OFF TIMER: The A14 can be configured to automatically power off if
unused for a specified period. If no changes are made to the unit within
the specified "Off Timer" period, the unit will automatically go to STANDBY
mode. The auto Power off timer will be restarted if changes are made
to the volume, source or playback. The default for Auto Power Off is set
to DISABLE.
Valid settings include: DISABLE, 1 HOUR, 2 HOURS, 5 HOURS, 12 HOURS.
• SIGNAL SENSE: Check if a digital audio signal is present on the configured
Signal Sense input. When this input is selected as the active listening
source, the A14 monitors the digital data stream to determine if there is
audio. If there is no audio detected for 10 minutes, the A14 will enter
Signal Sense Standby Mode. When in Signal Sense Standby Mode and
the A14 detects audio on Signal Sense input, the unit will automatically
power on. To disable this function, select the OFF option which is the
factory default setting.
NOTE: To use the Signal Sense function, the A14 must be actively
listening to the configured Signal Sense source. If a source other than
the configured Signal Sense source is selected, the automatic power
off and power on functions will not be active. Example: if the Signal
Sense source is configured as COAX 1 and the unit is listening to OPT
2, the signal sense functions will not be activated.
NOTE: When the A14 enters standby mode via the remote control,
the Signal Sense function will not operate until the unit detects the
audio has stopped for the minimum 10 minute time-out period. This
prevents the unit from immediately powering back on if there is still
active audio playing.
NOTE: When the SIGNAL SENSE function is activated the A14 will
consume additional power in signal sense standby mode.
• FIXED GAIN: Configures a Fixed Volume level for a specified input. To
enable this feature, select the desired fixed volume level for AUX1, AUX2,
USB, PC-USB, Optical 1, Optical 2, Coax 1, Coax 2, or Bluetooth. When
enabled and the input with a Fixed Volume is selected, the Volume level
will immediately be set to the specified level.
Valid settings include: VARIABLE, FIXED MIN, FIXED 01-95, FIXED MAX.
• AUX1 VOL: VARIABLE (disabled) is factory default.
• AUX2 VOL: VARIABLE (disabled) is factory default.
• USB VOL: VARIABLE (disabled) is factory default.
• PC-USB VOL: VARIABLE (disabled) is factory default.
• OPT1 VOL: VARIABLE (disabled) is factory default.
• OPT2 VOL: VARIABLE (disabled) is factory default.
• COAX1 VOL: VARIABLE (disabled) is factory default.
• COAX2 VOL: VARIABLE (disabled) is factory default.
• BTOOTH VOL: VARIABLE (disabled) is factory default.
NOTE: The Volume knob on the front panel and Volume +/- buttons
on the IR remote are disabled when the volume is Fixed. To disable this
feature set the Fixed Volume level to "Variable".
• PC-USB CLASS: Change supported PC-USB Audio Class of the attached
device.
NOTE: Some computers attached to the PC-USB do not support USB
Audio Class 2.0 and do not support 24/192 audio playback. If needed
the PC-USB can be configured for USB Audio Class 1.0. Please refer
to your computer operating system for details.
• VIEW NETWORK: Shows the network connection status and to view
the network settings. To view the network settings, press the + button on
the front panel or the ENT button on the remote control. If the network is
properly configured and attached, "Connected" will be displayed. To view
additional network configuration details, including IP Address information,
press the MENU button to toggle through the settings.
• CONFIGURE NETWORK: Allows configuration of the network IP settings.
To enter the Network Configuration menu option press the + button on the
front panel or the ENT button on the remote control.
NOTE: Configuration of the network requires the use of the remote
control to enter the IP address details. This setup cannot be completed
using the front panel controls. Please ensure you have access to the
remote control before proceeding with Network Configuration.
To begin configuration of the network, press the ENT button on the remote
control and follow as below:
The A14 supports both DHCP and STATIC IP addressing. Select the desired
IP address method with the left/right arrow buttons on the remote control
and press ENT to confirm.
If DHCP is selected, the A14 will refresh the IP address after pressing the ENT
button on the remote control to confirm. The refresh process could take up
to 10 seconds. The display will indicate if the DHCP refresh was successful.
If the refresh process failed, check the network connections and try again
by pressing the ENT button on the remote control. To exit the DHCP refresh
process, press the MENU button.
If STATIC IP address mode is selected, you must configure all settings for the
network, including IP Address, Subnet Mask, Gateway and DNS Server.
Use the up/down arrow buttons on the remote control to adjust the values
and press the left/right buttons on the remote control to move to the next
section. When the proper IP information is configured press ENT to confirm.
NOTE: For more information regarding network connection please
contact your authorized Rotel dealer.
NOTE: A network connection is not required for the A14 to operate.
• S/W VERSION: This shows the current software version loaded into the
A14. The software can be updated if the A14 is properly connected to
the Internet.
• Press the + button on the front panel to check if a new software
version is available.
A14 Stereo Integrated Amplifier